Omron Q2A Series Technical Manual page 403

No.
Name
(Hex.)
b5-57 PID FdbkMon Bias
(11DD)
b5-58 to b5-60 PID Setpoint 2 to PID
Setpoint 4
(1182 - 1184)
RUN
b5-61 PID LoLim Select for
Trim Mode
(119A)
b5-62 PID LoLim Value for
Trim Mode
(119B)
b5-63 PID DifFB Mon
Selection
(119C)
b5-64 PID DifFB Mon Gain
(119D)
b5-65 PID DifFB Mon Bias
(119F)
b5-66 PID Fback Mon Level
(11DE)
b5-67 PID DifFB Mon Level
(11DF)
b5-89 Sleep Method Selection
(0B89)
RUN
b5-90 EZsleep Unit
(0B90)
b5-91 EZsleep Min Spd
(0B91)
RUN
b5-92 EZsleep Level
(0B92)
RUN
b5-93 EZsleep Time
(0B93)
RUN
b5-94 EZsleep Wake Level
(0B94)
RUN
b5-95 EZsleep Wake Mode
(0B95)
b5-96 EZsleep Wake Time
(0B96)
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Description
V/f CL-V/f OLV CLV AOLV
Sets the bias for the monitor specified in b5-55 [PID Fback Mon Selection].
V/f CL-V/f OLV CLV AOLV
Sets the PID setpoint when H1-xx = 77 or 78 [MFDI Function Select = PID SP
Selection 1/2]. This value is a percentage where E1-04 [Max Output Frequency] setting
= a setting value of 100%.
V/f CL-V/f OLV CLV AOLV
Sets the function that adjusts the PID output in relation to the frequency reference.
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
Sets the lower limit of the PID frequency reference trim as a percentage where E1-04
[Max Output Frequency] setting = a setting value of 100%.
V/f CL-V/f OLV CLV AOLV
Sets the monitor for PID Differential Feedback (Ux-xx).
V/f CL-V/f OLV CLV AOLV
Sets the gain for the monitor specified in b5-63 [PID DifFB Mon Selection].
V/f CL-V/f OLV CLV AOLV
Sets the bias for the monitor specified in b5-63 [PID DifFB Mon Selection].
V/f CL-V/f OLV CLV AOLV
Sets the signal level for the monitor specified in b5-55 [PID Fback Mon Selection].
0 : Absolute
1 : Bi-directional (+/-)
V/f CL-V/f OLV CLV AOLV
Sets the signal level for the monitor specified in b5-63 [PID DifFB Mon Selection].
0 : Absolute
1 : Bi-directional (+/-)
V/f CL-V/f OLV CLV AOLV
Sets sleep and wake up operation when using PID.
0 : Standard
1 : EZ Sleep/Wake-up
V/f CL-V/f OLV CLV AOLV
Sets the measurement units for b5-91 [EZsleep Min Spd] and b5-92 [EZsleep Level].
0 : rpm
1 : 0.1Hz units
V/f CL-V/f OLV CLV AOLV
Sets the minimum speed for the EZ Sleep/Wakeup function. This parameter uses the
largest value from b5-91, b5-34 [PID Out Low Limit Level], and d2-02 [FRef Lower
Limit].
V/f CL-V/f OLV CLV AOLV
Sets the value that the output frequency or motor speed must be less than for longer than
b5-93 [EZsleep Time] to enter Sleep Mode.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that the output frequency or motor speed must be less than b5-92
[EZsleep Level] to enter Sleep Mode.
V/f CL-V/f OLV CLV AOLV
Sets the level at which the drive resumes operation when exiting Sleep Mode.
V/f CL-V/f OLV CLV AOLV
Sets the wake-up mode to use when exiting Sleep Mode.
0 : Setpoint Delta
1 : Absolute
V/f CL-V/f OLV CLV AOLV
Sets the EZ Wake-up time.
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
11.3 b: APPLICATION
Default
Ref.
(Range)
0.00 552
(-10.00 - +10.00)
0.00% 552
(0.00 - 100.00%)
0 553
(0, 1)
0.00% 553
(0.00 - 100.00%)
000 553
(000 - 999)
1.00 553
(0.00 - 10.00)
0.00 554
(-10.00 - +10.00)
0 554
(0, 1)
0 554
(0, 1)
0 554
(0, 1)
1 554
(0, 1)
0.0 Hz or 0 rpm (r/min) 554
(0.0 to 590.0 Hz or 0 to
35400 rpm (r/min))
0.0 Hz or 0 rpm (r/min) 555
(0.0 to 590.0 Hz or 0 to
35400 rpm (r/min))
5.0 s 555
(0.0 - 1000.0 s)
0.00% 555
(0.00 - 600.00%)
1 555
(0, 1)
1.0 s 555
(0.0 - 1000.0 s)
403
11