Omron Q2A Series Technical Manual page 402

11.3 b: APPLICATION
No.
Name
(Hex.)
b5-14 Fdback Loss Time
(01B2)
b5-15 Sleep Start Level
(01B3)
b5-16 Sleep Delay Time
(01B4)
b5-17 PID Accel/Decel Time
(01B5)
b5-18 b5-19 PID SP Selection
(01DC)
b5-19 PID Setpoint Value
(01DD)
RUN
b5-20 PID Unit Selection
(01E2)
b5-34 PID Out Low Limit
Level
(019F)
RUN
b5-35 PID In Hi Limit Level
(01A0)
RUN
b5-36 PID HiHi Limit Level
(01A1)
b5-37 PID HiHi Time
(01A2)
b5-38 PID SP User Scale for
Display
(01FE)
b5-39 PID SP User digits for
Display
(01FF)
b5-40 Fref Mon@PID
(017F)
b5-47 PID Out Rev Operation
Mode
(017D)
b5-53 PID I Ramp Limit
(0B8F)
RUN
b5-54 PID Softstarter Selection
(0BB7)
b5-55 PID Fback Mon
Selection
(0BE1)
b5-56 PID FdbkMon Gain
(0BE2)
402
Description
V/f CL-V/f OLV CLV AOLV
Sets the length of time that PID Feedback must be less than b5-13 [Fdback Loss Lvl] to
detect PID Feedback Loss [FbL].
V/f CL-V/f OLV CLV AOLV
Sets the output level that triggers the PID Sleep function.
V/f CL-V/f OLV CLV AOLV
Sets a delay time to start or stop the PID Sleep function.
V/f CL-V/f OLV CLV AOLV
Raises or lowers the PID setpoint using the acceleration and deceleration times set to
the drive. This is a soft-starter for the PID setpoint.
V/f CL-V/f OLV CLV AOLV
Sets the function that enables and disables b5-19 [PID Setpoint Value].
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
Sets the PID setpoint when b5-18 = 1 [b5-19 PID SP Selection = Enabled].
V/f CL-V/f OLV CLV AOLV
Sets the units to set and show b5-19 [PID Setpoint Value].
0 : 1 : 0.01Hz units
1 : 0.01% units
2 : rpm
3 : User Units
V/f CL-V/f OLV CLV AOLV
Sets the output lower limit for the PID control as a percentage of E1-04 [Max Output
Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the input upper limit for the PID control as a percentage of E1-04 [Max Output
Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the level that triggers Excessive PID Feedback [FbH] as a percentage of E1-04
[Max Output Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the length of time that the feedback signal must be more than the level set in b5-36
[PID HiHi Limit Level] to cause Excessive PID Feedback [FbH].
V/f CL-V/f OLV CLV AOLV
Sets the display for U5-01, U5-04 when the drive operates at the maximum output
frequency.
V/f CL-V/f OLV CLV AOLV
Sets the number of digits to set and show the PID setpoint.
0 : No Decimal Places
1 : 1 Decimal Place
2 : 2 decimal places
3 : 3 Decimal Places
V/f CL-V/f OLV CLV AOLV
Sets the contents for monitor U1-01 [Frequency Reference] in PID control.
0 : U1-01 with PID Output
1 : U1-01 without PID Output
V/f CL-V/f OLV CLV AOLV
Sets reverse motor rotation when the PID control output is negative.
0 : Lower Limit is Zero
1 : Negative Output Accepted
V/f CL-V/f OLV CLV AOLV
Sets the responsiveness of PID control when the PID feedback changes quickly.
V/f CL-V/f OLV CLV AOLV
Sets how the soft-starter responds to PID input/output.
0 : Disab PID Softstart
1 : Enab PID Softstart
V/f CL-V/f OLV CLV AOLV
Sets the monitor for PID Feedback (Ux-xx).
V/f CL-V/f OLV CLV AOLV
Sets the gain for the monitor specified in b5-55 [PID Fback Mon Selection].
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Default
Ref.
(Range)
1.0 s 549
(0.0 - 25.5 s)
Determined by A1-02 549
(0.0 - 590.0)
0.0 s 549
(0.0 - 25.5 s)
0.5 s 549
(0.0 - 6000.0 s)
0 549
(0, 1)
0.00% 550
(0.00 - 100.00%)
1 550
(0 - 3)
0.0% 550
(-100.0 - +100.0%)
1000.0% 550
(0.0 - 1000.0%)
100% 550
(0 - 100%)
1.0 s 550
(0.0 - 25.5 s)
Determined by b5-20 551
(1 - 60000)
2 551
(0 - 3)
0 551
(0, 1)
1 551
(0, 1)
0.0 Hz 551
(0.0 - 10.0 Hz)
1 552
(0, 1)
000 552
(000 - 999)
1.00 552
(0.00 - 10.00)