Multi-Function Analog Input Setting Values - Omron Q2A Series Technical Manual

Adds the offset value for the analog input value. For voltage input, this parameter will set the offset when a signal
of 0 V is input. For current input, this parameter will set the offset when a signal of 4 mA [H3-09 = 2] or 0 mA
[H3-09 = 3] is input.
■
H3-18 AI3 Offset
No.
Name
(Hex.)
H3-18 AI3 Offset
(02F2)
Adds the offset value for the analog input value. For voltage input, this parameter will set the offset when a signal
of 0 V is input. For current input, this parameter will set the offset when a signal of 4 mA [H3-05 = 2] or 0 mA
[H3-05 = 3] is input.
■
H3-40 15C1h Input Function
No.
Name
(Hex.)
H3-40 15C1h Input Function
(0B5C)
You can use the MFAI function from Modbus communications. Use this parameter to set the function. Sets the
input for the function in Modbus register 15C1. Refer to H3-xx "MFAI Setting Values" for the setting values.
■
H3-41 15C2h Input Function
No.
Name
(Hex.)
H3-41 15C2h Input Function
(0B5F)
Refer to H3-xx "MFAI Setting Values" for the setting values.
■
H3-42 15C3h Input Function
No.
Name
(Hex.)
H3-42 15C3h Input Function
(0B62)
Refer to H3-xx "MFAI Setting Values" for the setting values.
■
H3-43 Mbus In FilterTime Const
No.
Name
(Hex.)
H3-43 Mbus In FilterTime Const
(117F)
◆

Multi-Function Analog Input Setting Values

This section gives information about the functions set with H3-02, H3-06, and H3-10.
■
0: Through Mode
Setting Function
0 Through Mode
When you set a terminal that is not in use to 0, you can use the signal input to the terminal as PLC analog signal
input through Modbus communications or the communication option. This input signal does not have an effect on
drive operation. This functions the same as setting 100 (Through Mode).
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
V/f CL-V/f OLV CLV AOLV
Sets the offset level for analog signals input to terminal AI3. Usually it is not necessary to change
this setting.
V/f CL-V/f OLV CLV AOLV
Sets the Modbus AI1 function.
V/f CL-V/f OLV CLV AOLV
Sets the Modbus AI2 function.
V/f CL-V/f OLV CLV AOLV
Sets the Modbus AI3 function.
V/f CL-V/f OLV CLV AOLV
Sets the time constant to apply a primary delay filter to the Modbus analog input terminal.
V/f CL-V/f OLV CLV AOLV
Value for terminals that are not being used or terminals being used in through mode.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
12.7 H: TERMINALS
Default
(Range)
0
(-500 - +500)
Default
(Range)
0
(0, 3, 6 - 2F)
Default
(Range)
0
(0, 3, 6 - 2F)
Default
(Range)
0
(0, 3, 6 - 2F)
Default
(Range)
0.00 s
(0.00 - 2.00 s)
717
12