Omron Q2A Series Technical Manual page 484

11.16 A1-02 [Control Method] Dependent Parameters
Parameter
L1-01 Motor Cool Type for OL1
Calc
L3-05 StallP@RUN Enable
L3-20 DCBus VoltAdj Gain
L3-21 OVSup Acc/Dec Gain
L3-36 VibSup Gain@Accel
L4-01 SpAgree Det.Level
L4-02 SpAgree Det.Width
L4-03 SpAgree Det.Level(+/-)
L4-04 SpAgree Det.Width(+/-)
L8-38 Carrier Reduction Mode
L8-40 Carrier Red Off-Delay Time
n1-15 PWM VOffset Calibration
o1-03 FrqDisplay Unit Selection
o1-04 V/f Pattern Unit for Display
*1 Drive models and 4103 to 4675 use these default settings when C6-01 = 1 [ND/HD Duty Selection = ND Rating]. Drive models
4140 to 4675 use these default settings when C6-01 = 0 [ND/HD Duty Selection = HD Rating].
• A1-02 = 2 [Control Method = OLVector]：2.00
• A1-02 = 3, 4 [Control Method = CLVector, Adv OLVector]：0.05
*2 The default setting is 1000 ms for drive models 4103 to 4675.
*3 The default setting varies depending on the setting of C6-01 [ND/HD Duty Selection].
*4 The setting range varies depending on the setting of E5-03 [PM Mot Rated Current (FLA)] when A1-02 = 5 [Control Method = PM
OLVector].
*5 The default setting varies depending on drive model and E1-03 [V/f Pattern Selection] settings.
*6 This is the value for 200 V class drives. Double the value for 400 V class drives.
*7 The maximum value within the setting range is 100.0 when A1-02 = 5 or 7 [Control Method = PM OLVector or PM CLVector].
*8 The setting range is -100.0 to 100.0 when A1-02 = 5 or 7 [Control Method = PM OLVector or PM CLVector].
◆
Control Method for PM Motors and Simple Vector Control
No.
b2-01 ZSpd/DCI Threshold
b2-04 DCInj Time@Stop
b3-01 SpSrch@Start Selection
b3-14 Speed Bi-Directional Search
b5-15 Sleep Start Level
b6-01 Dwell Ref.@Start
b6-03 Dwell Ref@Stop
b8-02 eSave Ctrl Gain
b8-03 eSave Filter Time
C1-11 Ac/Dec Switch Frequency
C2-01 Jerk@Start of Accel
C3-01 Slip Comp Gain
C3-02 Slip Comp Delay Time
C4-01 Trq Comp Gain
C4-02 Trq Comp Delay Time
C5-01 ASR PGain 1
484
Setting Range Unit
0 - 4 1
0 - 3 1
0.00 - 5.00 0.01
0.10 - 10.00 0.01
0.0 - 100.0 0.1
*7
0.0 - 400.0 0.1
0.0 - 20.0 0.1
-400.0 - +400.0
0.1
*8
0.0 - 20.0 0.1
0 - 2 1
0.00 - 2.00 0.01 s
0 - 2 1
0 - 3 1
0 - 1 1
Setting Range Unit
0.0 - 10.0 0.1
0.00 - 10.00 0.01 s
0 - 1 1
0 - 1 1
*1
0.0 - 400.0 0.1
*1
0.0 - 400.0 0.1
*1
0.0 - 400.0 0.1
0.0 - 10.0 0.1
0.00 - 10.00 0.01 s
*1
0.0 - 400.0 0.1
0.00 - 10.00 0.01 s
0.0 - 2.5 0.1
0 - 10000 1 ms
0.00 - 2.50 0.01
0 - 10000 1 ms
0.00 - 300.00 0.01
Control Method
V/f Control PG V/f Control
(0) (1)
1 1
1 1
1.00 1.00
1.00 1.00
10.0 10.0
0.0 Hz 0.0 Hz
2.0 Hz 2.0 Hz
0.0 Hz 0.0 Hz
2.0 Hz 2.0 Hz
*3 *3
0.50 0.50
1 1
0 0
- -
PM OLVector PM AOLVector
(5)
0.5 Hz 1.0%
0.00
0
1
0.0 Hz 0.0 %
0.0 Hz 0.0 %
0.0 Hz 0.0 %
-
-
0.0 Hz 0.0 %
1.00
-
-
0.00
100
10.00 10.00
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
OLVector CLVector
(2) (3)
1 1
- -
0.30 0.30
1.00 1.00
20.0 -
0.0 Hz 0.0 Hz
2.0 Hz 2.0 Hz
0.0 Hz 0.0 Hz
2.0 Hz 2.0 Hz
*3 *3
0.50 0.50
1 1
0 0
- 0
Control Method
PM CLVector
(6) (7)
0.5%
0.00 0.00
0 1
1 1
0.0 %
0.0 %
0.0 %
- -
- -
0.0 %
0.20 0.20
- -
- -
- -
- -
20.00
Adv OLVector
(4)
1
-
0.30
1.00
-
0.0 Hz
2.0 Hz
0.0 Hz
2.0 Hz
*3
0.50
2
0
0
EZ Vector
(8)
1.0%
0.00
0
1
0.0 %
0.0 %
0.0 %
-
-
0.0 %
1.00
Determined by E9-
01
200
0.00
100
10.00