Omron Q2A Series Technical Manual page 432

11.8 H: TERMINALS
Setting Function
11 LOC/REM Sel.
12 AI Input Sel
13 Spd/Trq Switch
14 AI Trq Polarity
15 FWD/REV Det
16 Ref Sample
17 Ac/Dec Hold
18 Ac/Dec Time1
19 Ac/Dec Time2
1A Drive Enable
1B Baseblock NO
1E Baseblock NC
20 to 2F External Fault
30 DCInj Cmd
31 Zero Servo
432
V/f CL-V/f OLV CLV AOLV
Sets drive control for the keypad (LOCAL) or an external source (REMOTE).
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
Sets the command that enables or disables the terminals selected in H3-14 [An.In Term.Enable Sel].
ON : Input to the terminal selected with H3-14 is enabled
OFF : Input to the terminal selected with H3-14 is disabled
V/f CL-V/f OLV CLV AOLV
Sets the function to switch between torque control and speed control.
ON : Torque control
OFF : Speed control
V/f CL-V/f OLV CLV AOLV
Sets the rotation direction of the external torque reference.
ON : External torque reference reverse direction
OFF : External torque reference forward direction
V/f CL-V/f OLV CLV AOLV
Sets the rotation direction of the motor when in Simple Closed Loop V/f Control method and F1-21, F1-37 = 0
[Encoder Option Function Selection = A Pulse Detection], or when in Closed Loop V/f Control method.
ON : Reverse
OFF : Forward
V/f CL-V/f OLV CLV AOLV
Sets the command to sample the frequency reference at terminals AI1, AI2, or AI3 and hold the frequency
reference at that frequency.
V/f CL-V/f OLV CLV AOLV
Momentarily pauses motor acceleration and deceleration when the terminal is turned ON, retains the output
frequency that was stored in the drive at the time of the pause, and restarts motor operation.
V/f CL-V/f OLV CLV AOLV
Sets the drive to use C1-01, C1-02 [Accel Time 1, Decel Time 1] or C1-03, C1-04 [Accel Time 2, Decel Time 2].
V/f CL-V/f OLV CLV AOLV
Set this function and H1-xx = 18 [Ac/Dec Time1] together. Sets the drive to use C1-05, C1-06 [Accel Time 3, Decel
Time 3] or C1-07, C1-08 [Accel Time 4, Decel Time 4].
V/f CL-V/f OLV CLV AOLV
Sets the function to show dnE [Drive Enabled] on the keypad and ignore Run commands when the terminal is
OFF.
V/f CL-V/f OLV CLV AOLV
Sets the command that stops drive output and coasts the motor to stop when the input is ON.
ON : Baseblock (drive output stop)
OFF : Normal operation
V/f CL-V/f OLV CLV AOLV
Sets the command that stops drive output and coasts the motor to stop when the input terminal is OFF.
ON : Normal operation
OFF : Baseblock (drive output stop)
V/f CL-V/f OLV CLV AOLV
Sets a command to stop the drive when a failure or fault occurs on an external device.
20 : ExF NO-AlRmp
21 : ExF NC-AlRmp
22 : ExF NO-RnRmp
23 : ExF NC-RnRmp
24 : ExF NO-AlCoast
25 : ExF NC-AlCoast
26 : ExF NO-RnCoast
27 : ExF NC-RnCoast
28 : ExF NO-AlFStop
29 : ExF NC-AlFStop
2A : ExF NO-RnFStop
2B : ExF NC-RnFStop
2C : ExF NO-AlAlarm
2D : ExF NC-AlAlarm
2E : ExF NO-RnAlarm
2F : ExF NC-RnAlarm
V/f CL-V/f OLV CLV AOLV
Sets the command to use DC Injection Braking to stop the motor.
Note:
When A1-02 = 8 [Control Method = EZ Vector], this function is available if you use a PM motor.
V/f CL-V/f OLV CLV AOLV
Sets the function to hold a stopped motor.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Ref.
673
674
674
674
674
674
675
675
675
675
676
676
676
677
677