Omron Q2A Series Technical Manual page 485

No.
C5-02 ASR ITime 1
C5-03 ASR PGain 2
C5-04 ASR ITime 2
C5-06 ASR Delay Time
C5-07 ASR Gain Switch Frequency
C6-02 Carrier Frequency Selection
d3-01 Jump Frequency 1
d3-02 Jump Frequency 2
d3-03 Jump Frequency 3
d3-04 Jump Frequency Width
d5-02 Torque Ref Delay Time
E1-04 Max Output Frequency
E1-05 Max Output Voltage
E1-06 Base Frequency
E1-07 Mid A Frequency
E1-08 Mid A Voltage
E1-09 Min Output Frequency
E1-10 Min Output Voltage
F1-01 Enc1 Pulse Count (PPR)
F1-05 Enc1 Rotat Selection
F1-09 Overspeed Delay Time
H4-20 An.Pwr Mon 100% Level
L1-01 Motor Cool Type for OL1 Calc
L3-05 StallP@RUN Enable
L3-20 DCBus VoltAdj Gain
L3-21 OVSup Acc/Dec Gain
L3-36 VibSup Gain@Accel
L4-01 SpAgree Det.Level
L4-02 SpAgree Det.Width
L4-03 SpAgree Det.Level(+/-)
L4-04 SpAgree Det.Width(+/-)
L8-38 Carrier Reduction Mode
L8-40 Carrier Red Off-Delay Time
n1-15 PWM VOffset Calibration
o1-03 FrqDisplay Unit Selection
o1-04 V/f Pattern Unit for Display
*1 The setting range is 0.0 to 100.0 when A1-02 = 6 or 7 [Control Method = PM AOLVector or PM CLVector].
*2 The setting range is 0.0 to 40.0 when A1-02 = 6 or 7 [Control Method = PM AOLVector or PM CLVector].
*3 The default setting varies depending on the setting of ND/HD Duty Selection.
*4 This is the value for 200 V class drives. Double the value for 400 V class drives.
*5 The setting range is -100.0 to +100.0 when A1-02 = 6 or 7 [Control Method = PM AOLVector or PM CLVector].
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Setting Range Unit
0.000 - 60.000 0.001 s
0.00 - 300.00 0.01
0.000 - 10.000 0.001 s
0.000 - 0.500 0.001 s
*1
0.0 - 400.0 0.1
1 - F 1
*1
0.0 - 400.0 0.1
*1
0.0 - 400.0 0.1
*1
0.0 - 400.0 0.1
*2
0.0 - 20.0 0.1
0 - 1000 1 ms
*3
40.0 - 400.0 0.1 Hz
*4
0.0 - 255.0 0.1 V
0.0 - 400.0 0.1 Hz
0.0 - 400.0 0.1 Hz
*4
0.0 - 255.0 0.1 V
0.0 - 400.0 0.1 Hz
*4
0.0 - 255.0 0.1 V
0 - 60000 1 ppr
0 - 1 1
0.0 - 2.0 0.1 s
0.00 - 650.00 0.01
0 - 4 1
0 - 3 1
0.00 - 5.00 0.01
0.10 - 10.00 0.01
0.0 - 100.0 0.1
*1
0.0 - 400.0 0.1
*2
0.0 - 20.0 0.1
*5
-400.0 - +400.0 0.1
*2
0.0 - 20.0 0.1
0 - 2 1
0.00 - 2.00 0.01 s
0 - 2 1
0 - 3 1
0 - 1 1
11.16 A1-02 [Control Method] Dependent Parameters
Control Method
PM OLVector PM AOLVector
(5) (6)
0.500 0.500
- 10.00
- 0.500
- 0.016
0.0 Hz 0.0 %
2 2
0.0 Hz 0.0 %
0.0 Hz 0.0 %
0.0 Hz 0.0 %
1.0 Hz 1.0 %
- -
Determined by E5- Determined by E5-
01 01
Determined by E5- Determined by E5-
01 01
Determined by E5- Determined by E5-
01 01
- -
- -
Determined by E5- Determined by E5-
01 01
- -
1024 1024
1 1
- -
Determined by E5- Determined by E5-
01 01
4 4
1 -
0.65 0.65
1.00 1.00
- -
0.0 Hz 0.0 %
2.0 Hz 4.0%
0.0 Hz 0.0 %
2.0 Hz 4.0%
0 0
0.00 0.00
1 1
0 1
- 1
PM CLVector EZ Vector
(7) (8)
0.500 0.500
20.00 10.00
0.500 0.500
0.004 0.004
0.0 % 0.0 %
2 2
0.0 % 0.0 %
0.0 % 0.0 %
0.0 % 0.0 %
1.0 % 1.0 %
0 -
Determined by E5-
-
01
Determined by E5-
-
01
Determined by E5-
-
01
- -
- -
0.0 -
- -
1024 600
1 0
0.0 -
Determined by E5- Determined by E9-
01 07
Determined by E9-
5
01
- 3
0.65 0.65
1.00 1.00
- -
0.0 % 0.0 %
4.0% 4.0%
0.0 % 0.0 %
4.0% 4.0%
0 0
0.00 0.00
1 1
1 1
1 -
485
11