Omron Q2A Series Technical Manual page 192

5.3 UL Standards
Screw Adapter
Bit
M4
Bit
*1
M5
Bit
M6
Bit
M6
Bit
M8
Bit
M10
*1 When wiring drive models 4089 and smaller, select the correct tools for the wire gauge.
*2 Use 6.35 mm (0.25 in) bit socket holder.
*3 Use a torque wrench that can apply this torque measurement range.
■
Main Circuit Wire Gauges and Tightening Torques
Comply with local standards for correct wire gauges in the region where the drive is used.
WARNING! Electrical Shock Hazard. Only connect peripheral options, for example a DC reactor or braking resistor, to terminals
+1, +2, +3, -, B1, and B2. Failure to obey can cause death or serious injury.
Refer to Wire Gauges and Tightening Torques on page
Drives from model 4208, use UL-approved closed-loop crimp terminals on the drive main circuit terminals. Use
the tools recommend by the terminal manufacturer and make sure that the terminals are correctly connected.
Select the correct wires for main circuit wiring.
Three-Phase 400 V Class
Model Terminals
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4002 -, +1, +2
B1, B2
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4004 -, +1, +2
B1, B2
192
Table 5.7 Recommended Wiring Tools
Bit
Model Manufacturer
SF-BIT-SL 1,0X4,0-70 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 5-50 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 6-50 PHOENIX CONTACT
SF-BIT-HEX 8-50 PHOENIX CONTACT
Applicable Gauge
Recommended
(IP20 Applicable
Gauge
*1
Gauge
AWG, kcmil
AWG, kcmil
14 - 6
14
(14 - 6)
14 - 6
14
(14 - 6)
14 - 3
14
(14 - 3)
14 - 10
14
(14 - 10)
14 - 8
12
(-)
14 - 6
14
(14 - 6)
14 - 6
14
(14 - 6)
14 - 3
14
(14 - 3)
14 - 10
14
(14 - 10)
14 - 8
12
(-)
Torque Driver Model
(Tightening Torque)
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge ≤ 25 mm
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge ≥ 30 mm
-
-
-
-
-
75for general conditions
Wire
Stripping
*2
Length
)
Size
mm
10 M4
10 M4
18 M5
10 M4
- M4
10 M4
10 M4
18 M5
10 M4
- M4
SIEPYEUOQ2A01A AC Drive Q2A Technical Manual
Torque Wrench
-
2
(AWG 10):
Wire Gauge ≤ 25 mm
-
2 (AWG 8): Wire Gauge ≥ 30 mm
4.1 - 4.5 N∙m
*2 *3
5 - 9 N∙m
3 - 3.5 N∙m
8 - 12 N∙m
12 - 14 N∙m
Terminal Screw
Tightening Torque
N∙m (lb∙in.)
Shape
Slotted (-)
(13.5 - 15)
Slotted (-)
(13.5 - 15)
Slotted (-)
(19.8 - 22)
Slotted (-)
(13.5 - 15)
Phillips/slotted combo
(10.6 - 13.3)
Slotted (-)
(13.5 - 15)
Slotted (-)
(13.5 - 15)
Slotted (-)
(19.8 - 22)
Slotted (-)
(13.5 - 15)
Phillips/slotted combo
(10.6 - 13.3)
2 (AWG 10):
2 (AWG 8):
*2 *3
*2 *3
*2 *3
*2 *3
1.5 - 1.7
1.5 - 1.7
2.3 - 2.5
*3
1.5 - 1.7
1.2 - 1.5
1.5 - 1.7
1.5 - 1.7
2.3 - 2.5
*3
1.5 - 1.7
1.2 - 1.5