Siemens SINAMICS G120D CU240D-2 DP Manual page 578

2 Parameters
2.4 BICO parameters (connectors/binectors)
p1455[0...n]
p1466[0...n]
p1475[0...n]
p1478[0...n]
p1479[0...n]
p1486[0...n]
p1503[0...n]
p1511[0...n]
p1512[0...n]
p1513[0...n]
p1522[0...n]
p1523[0...n]
p1528[0...n]
p1529[0...n]
p1552[0...n]
p1554[0...n]
p2016[0...3]
p2051[0...16]
p2061[0...15]
p2099[0...1]
p2151[0...n]
p2253[0...n]
p2254[0...n]
p2264[0...n]
p2289[0...n]
p2296[0...n]
p2297[0...n]
p2298[0...n]
p2299[0...n]
p2513[0...3]
p2515[0...3]
p2516[0...3]
p2530
p2531
p2532
p2537
p2541
p2555
p2578
p2579
p2593
p2594[0...2]
p2598[0...3]
p2642
p2643
p2644
p2645
p2646
p2654
p2657
p2660
p3230[0...n]
p8543
p20094[0...3]
p20098[0...3]
578
CI: Speed controller P gain adaptation signal / n_ctr adapt_sig Kp
CI: Speed controller P-gain scaling / n_ctrl Kp scal
CI: Speed controller torque setting value for motor holding brake / n_ctrl M_sv MHB
CI: Speed controller integrator setting value / n_ctr integ_setVal
CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
CI: Droop compensation torque / Droop M_comp
CI: Torque setpoint / M_set
CI: Supplementary torque 1 / M_suppl 1
CI: Supplementary torque 1 scaling / M_suppl 1 scal
CI: Supplementary torque 2 / M_suppl 2
CI: Torque limit upper / M_max upper
CI: Torque limit lower / M_max lower
CI: Torque limit upper scaling / M_max upper scal
CI: Torque limit lower scaling / M_max lower scal
CI: Torque limit upper scaling without offset / M_max up w/o offs
CI: Torque limit lower scaling without offset / M_max low w/o offs
CI: Comm IF USS PZD send word / Comm USS send word
CI: PROFIdrive PZD send word / PZD send word
CI: PROFIBUS PZD send double word / PZD send DW
CI: Connector-binector converter signal source / Con/bin S_src
CI: Speed setpoint for messages/signals / n_set for msg
CI: Technology controller setpoint 1 / Tec_ctrl setp 1
CI: Technology controller setpoint 2 / Tec_ctrl setp 2
CI: Technology controller actual value / Tec_ctrl act val
CI: Technology controller pre-control signal / Tec_ctr prectr_sig
CI: Technology controller output scaling / Tec_ctrl outp scal
CI: Technology controller maximum limit signal source / Tec_ctrMaxLimS_src
CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
CI: Technology controller limit offset / Tech_ctrl lim offs
CI: LR Position actual value preprocessing corrective value / Act val_prep corr
CI: LR position actual setting setting value / s_act set setVal
CI: LR position offset / Position offset
CI: LR position setpoint / s_set
CI: LR velocity setpoint / v_set
CI: LR position actual value / s_act
CI: LR position controller adaptation / Adaptation
CI: LR position controller output speed limit signal source / LR_out n_lim S_src
CI: LR LU/revolution LU/mm / LU/rev LU/mm
CI: EPOS software limit switch minus signal source / SW limSw Min S_src
CI: EPOS software limit switch plus signal source / SW limSwPlus S_src
CI: EPOS LU/revolution LU/mm / LU/rev LU/mm
CI: EPOS Maximum velocity externally limited / v_Max ext lim
CI: EPOS reference point coordinate signal source / Ref_pt coord S_src
CI: EPOS direct setpoint input/MDI position setpoint / MDI s_set
CI: EPOS direct setpoint input/MDI velocity setpoint / MDI v_set
CI: EPOS direct setpoint input/MDI acceleration override / MDI a_over
CI: EPOS direct setpoint input/MDI deceleration override / MDI -a_over
CI: EPOS velocity override / v_over
CI: EPOS direct setpoint input/MDI mode adaptation / MDI mode adapt
CI: EPOS position actual value/position setting value / Pos act/set value
CI: EPOS measured value referencing / Meas val ref
CI: Load monitoring speed actual value / Load monit n_act
CI: Active speed setpoint in the BOP/IOP manual mode / N_act act OP
CI: ADD 0 inputs / ADD 0 inputs
CI: ADD 1 inputs / ADD 1 inputs
SINAMICS G120D
List Manual (LH14), 01/2016, A5E33842313