Siemens SINAMICS G120D CU240D-2 DP Manual page 568

2 Parameters
2.3 Parameters for data sets
p2183[0...n]
p2184[0...n]
p2185[0...n]
p2186[0...n]
p2187[0...n]
p2188[0...n]
p2189[0...n]
p2190[0...n]
p2192[0...n]
p2193[0...n]
p2194[0...n]
p2195[0...n]
p2196[0...n]
p2201[0...n]
p2202[0...n]
p2203[0...n]
p2204[0...n]
p2205[0...n]
p2206[0...n]
p2207[0...n]
p2208[0...n]
p2209[0...n]
p2210[0...n]
p2211[0...n]
p2212[0...n]
p2213[0...n]
p2214[0...n]
p2215[0...n]
p2216[0...n]
p2230[0...n]
p2237[0...n]
p2238[0...n]
p2240[0...n]
p2247[0...n]
p2248[0...n]
p2502[0...n]
p2503[0...n]
p2504[0...n]
p2505[0...n]
p2506[0...n]
p2519[0...n]
p2533[0...n]
p2534[0...n]
p2535[0...n]
p2536[0...n]
p2538[0...n]
p2539[0...n]
p2546[0...n]
p2567[0...n]
p2634[0...n]
p2900[0...n]
p2901[0...n]
p2930[0...n]
p3231[0...n]
p3233[0...n]
568
Load monitoring speed threshold value 2 / n_thresh 2
Load monitoring speed threshold value 3 / n_thresh 3
Load monitoring torque threshold 1 upper / M_thresh 1 upper
Load monitoring torque threshold 1 lower / M_thresh 1 lower
Load monitoring torque threshold 2 upper / M_thresh 2 upper
Load monitoring torque threshold 2 lower / M_thresh 2 lower
Load monitoring torque threshold 3 upper / M_thresh 3 upper
Load monitoring torque threshold 3 lower / M_thresh 3 lower
Load monitoring delay time / Load monit t_del
Load monitoring configuration / Load monit config
Torque threshold value 2 / M_thresh val 2
Torque utilization switch-off delay / M_util t_off
Torque utilization scaling / M_util scal
CO: Technology controller fixed value 1 / Tec_ctrl fix val1
CO: Technology controller fixed value 2 / Tec_ctr fix val 2
CO: Technology controller fixed value 3 / Tec_ctr fix val 3
CO: Technology controller fixed value 4 / Tec_ctr fix val 4
CO: Technology controller fixed value 5 / Tec_ctr fix val 5
CO: Technology controller fixed value 6 / Tec_ctr fix val 6
CO: Technology controller fixed value 7 / Tec_ctr fix val 7
CO: Technology controller fixed value 8 / Tec_ctr fix val 8
CO: Technology controller fixed value 9 / Tec_ctr fix val 9
CO: Technology controller fixed value 10 / Tec_ctr fix val 10
CO: Technology controller fixed value 11 / Tec_ctr fix val 11
CO: Technology controller fixed value 12 / Tec_ctr fix val 12
CO: Technology controller fixed value 13 / Tec_ctr fix val 13
CO: Technology controller fixed value 14 / Tec_ctr fix val 14
CO: Technology controller fixed value 15 / Tec_ctr fix val 15
Technology controller fixed value selection method / Tec_ctr FixVal sel
Technology controller motorized potentiometer configuration / Tec_ctr mop config
Technology controller motorized potentiometer maximum value / Tec_ctrl mop max
Technology controller motorized potentiometer minimum value / Tec_ctrl mop min
Technology controller motorized potentiometer starting value / Tec_ctrl mop start
Technology controller motorized potentiometer ramp-up time / Tec_ctr mop t_r-up
Technology controller motorized potentiometer ramp-down time / Tec_ctrMop t_rdown
LR encoder assignment / Encoder assignment
LR length unit LU per 10 mm / LU per 10 mm
LR motor/load motor revolutions / Mot/load motor rev
LR motor/load load revolutions / Mot/load load rev
LR length unit LU per load revolution / LU per load rev
LR position actual value preprocessing config. DDS changeover / s_act config DDS
LR position setpoint filter time constant / s_set_filt T
LR speed pre-control factor / n_prectrl fact
LR speed pre-control balancing filter dead time / n_prectrFlt t_dead
LR speed pre-control symmetrizing filter PT1 / n_prectrl filt PT1
LR proportional gain / Kp
LR integral time / Tn
LR dynamic following error monitoring tolerance / s_delta_monit tol
LR torque pre-control moment of inertia / M_prectr M_inertia
EPOS fixed stop maximum following error / Following err max
CO: Fixed value 1 [%] / Fixed value 1 [%]
CO: Fixed value 2 [%] / Fixed value 2 [%]
CO: Fixed value M [Nm] / Fixed value M [Nm]
Load monitoring speed deviation / Load monit n_dev
Torque actual value filter time constant / M_act_filt T
SINAMICS G120D
List Manual (LH14), 01/2016, A5E33842313