Page 1
This document is “OKI DATA – CONFIDENTIAL” Only persons and parties authorised by OKI DATA have permissions to access this document. This document should not be accessed by any parties without the approval of OKI DATA. Anyone who is found to be contradicting the above may be subject to legal action.
Page 3
GENERAL PRECAUTIONS REGARDING THE SERVICE FOR ES9160 MFP / ES9170 MFP The installation and service shall be done by a qualified service technician. 1. Transportation/Installation When transporting/installing the equipment, employ two persons and be sure to hold the positions as shown in the figure.
Page 4
Be sure to handle/install them properly. If these parts are short-circuited and their functions become ineffective, they may result in fatal accidents such as burnout. Do not allow a short-circuit and do not use the parts not recommended by OKI DATA CORPORATION.
Page 5
4. Cautionary Labels During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the power cable during service”, “CAUTION. HOT”, “CAUTION. HIGH VOLTAGE”, “CAUTION. LASER BEAM”, etc. to see if there is any dirt on their surface and if they are properly stuck to the equipment.
Page 6
Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual. Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel. Vorsicht: Entsorgung der gebrauchten Batterien und IC-RAMs (inclusive der Lithium-Batterie) nach diesem Handbuch.
Page 7
ALLEGEMEINE SICHERHEITSMASSNAHMEN IN BEZUG AUF DIE WARTUNG FÜR ES9160 MFP / ES9170 MFP Die Installation und die Wartung sind von einem qualifizierten Service- Techniker durchzuführen. 1. Transport/Installation Zum Transportieren/Installieren des Gerätes werden 2 Personen benötigt. Nur an den in der Abbildung gezeigten Stellen tragen.
Page 8
Sie müssen unbedingt korrekt gehandhabt und installiert werden. Wenn diese Teile kurzgeschlossen und funktionsunfähig werden, kann dies zu schwerwiegenden Schäden, wie einem Abbrand, führen. Kurzschlüsse sind zu vermeiden, und es sind ausschließlich Teile zu verwenden, die von der OKI DATA CORPORATION. empfohlen sind.
Page 9
4. Warnetiketten Im Rahmen der Wartung unbedingt das Leistungsschild und die Etiketten mit Warnhinweisen überprüfen [z. B. „Unplug the power cable during service“ („Netzkabel vor Beginn der Wartungsarbeiten abziehen“), „CAUTION. HOT“ („VORSICHT, HEISS“), „CAUTION. HIGH VOLTAGE“ („VORSICHT, HOCHSPANNUNG“), „CAUTION. LASER BEAM“ („VORSICHT, LASER“) usw.], um sicherzustellen, dass sie nicht verschmutzt sind und korrekt am Gerät angebracht sind.
Page 10
Caution: Dispose of used batteries and IC-RAMs including lithium batteries according to this manual. Attention: Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel. Vorsicht: Entsorgung der gebrauchten Batterien und IC-RAMs (inclusive der Lithium-Batterie) nach diesem Handbuch.
Page 11
• Laseremissionseinheit Diese Einheit besteht aus der Laserdiode, dem Fokussierungsobjektiv, der Blende und dem Zylinderobjektiv. Laserdiode Diese Laserdiode zeichnet sich durch eine geringe Regeldifferenz, eine kleine Laservariation und einen niedrigen Schwellenstrom aus. Die Blende der Laseremissionseinheit ist unter dem Fokussierobjektiv angeordnet, um die Form der Laserstrahlen in der primären und sekundären Scanrichtung festzulegen.
Page 13
CONTENTS 1. FEATURES ........................1-1 Main Feature of ES9160 MFP / ES9170 MFP ..............1-1 2. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES ........2-1 Specifications ........................2-1 2.1.1 General ......................2-1 2.1.2 Copy ........................2-4 2.1.3 Print ........................2-7 2.1.4...
Page 18
6.5.1 Adjustment of smudged/faint text ..............6-30 6.5.2 Adjustment of image density................6-31 6.5.3 Gamma balance adjustment................6-32 Image Quality Adjustment (Scanning Function).............. 6-33 6.6.1 Gamma balance adjustment................6-33 6.6.2 Density adjustment ..................6-34 6.6.3 Judgment threshold for ACS................6-35 6.6.4 Sharpness adjustment ..................
Page 19
6.17.1 Adjusting the Alignment Position ..............6-102 6.17.2 Adjusting the Stapling Position ..............6-105 6.17.3 Stapling/folding position adjustment in saddle stitch unit....... 6-107 6.17.4 Saddle Stitch Skew Adjustment..............6-113 6.18 Adjustment of Hole punch unit (MJ-6007)..............6-114 6.18.1 Destination setting of hole punch control PC board........6-114 6.19 Adjustment of Hole punch unit (MJ-6008)..............
Page 20
7.11 Grease List........................7-52 7.12 Operational Items in Overhauling..................7-52 8. ERROR CODE AND TROUBLESHOOTING ..............8-1 General Descriptions......................8-1 Error Code List ........................8-2 8.2.1 Jam ........................8-2 8.2.2 Service call ...................... 8-12 8.2.3 Error in Internet FAX / Scanning Function ............8-19 8.2.4 Printer function error ..................
Page 21
8.4.16 Uneven image density ................... 8-277 8.4.17 Faded image (low density, abnormal gray balance) ........8-278 8.4.18 Image dislocation in feeding direction............8-279 8.4.19 Jittering image ....................8-280 8.4.20 Poor cleaning....................8-281 8.4.21 Uneven light distribution ................8-282 8.4.22 Blotched image ....................8-283 8.4.23 Black streaks on image leading edge during scanning........
Page 23
FEATURES Main Feature of ES9160 MFP / ES9170 MFP • The customizing ability is improved and high security performance is given by adopting a new OS. (New standard IEEE2600 embedded) • The open platform interface using Web Service is embedded.
Page 28
Leading / trailing edges: 4.2±2.0 mm, Side edges: 4.2±2.0 mm (print) Multiple copying....... Up to 999 copies; Key in set numbers First copy time ......ES9160 MFP: Approx.3.7 sec. or less ES9170 MFP: Approx.3.7 sec. or less (A4/LT, upper drawer, 100%, original placed manually) Copy speed (Copies/min.)
Page 445
- ES9160 MFP: every 125,000 sheets - ES9170 MFP: every 150,000 sheets • Values under “Replacement” indicate the replacement cycle for the ES9160 MFP or ES9170 MFP. • The replacement cycle of the parts in the feeding section equals to the number of sheets fed from each paper source.
Page 480
7.12 Operational Items in Overhauling Overhaul each equipment in the following timing. • ES9160 MFP: When the number of output pages has reached 375,000 or 2.5 years have passed from the start of use (Whichever comes earlier) • ES9170 MFP: When the number of output pages has reached 450,000 or 2.5 years have passed from the start of use (Whichever comes earlier) Replace all the supplies.
Page 924
13.3 Electric Parts Layout [A] Scanner unit, control panel [B] Power supply, developer unit [C] Laser unit, fuser unit, toner cartridge [D] Drive unit THMO1 THMS2 MOT2 LEDB THMS3 THMS1 THMO2 THMO3 LAMP3 CTIF LAMP1 CTRG THMS4 LAMP2 HVPS THMO4 LVPS [E] Automatic duplexing unit, transfer unit, exit unit [F] Bypass feed unit...
Page 925
Input check (Test mode 03) Items to be checked and the condition of the equipment when the buttons [A] to [H] are highlighted are liste [FAX] button: OFF/[COPY] button: OFF ([FAX] LED: OFF/[COPY] LED: OFF) Contents Highlighted display Normal display Digital Button Items to check...
Page 926
1st transport sensor (S21) Paper present No paper Tray at upper limit Other than upper Upper drawer tray-up sensor position limit position Upper drawer empty sensor No paper Paper present Upper drawer nearly empty sensor Drawer is nearly Paper present Upper drawer detection sensor Drawer not installed Drawer present 2nd transport sensor (S14)
Page 927
[FAX] button: ON/[COPY] button: OFF ([FAX] LED: ON/[COPY] LED: OFF) Contents Highlighted display Normal display Digital Button Items to check e.g. e.g. IPC board connection Not connected Connected MOT board connection Not connected Connected Key copy counter connection Not connected Connected Auto-toner sensor connection Not connected...
Page 928
Job Separator connection Not connected Connected Bridge unit connection Not connected Connected Offset Tray initial position detection Initial position Other than initial Bridge unit paper full detection Full Not full Bridge unit cover opening/closing switch Cover opened Cover closed Bridge unit paper exit sensor Paper present No paper Bridge unit transport sensor...
Page 929
Table 1. Relation between the status of the bypass paper width sensor and paper size (width). Paper width Bypass paper-width sensor size A3/A4 B4/B5 A4-R/A5 B5-R/B6 A5-R/A6 A6-R (Card LD/LT LG/LT-R/ST ST-R/COMP Table 2. Connecting status of additional options at inner area of the equipment None Bridge unit Offset Tray...
Page 930
[FAX] button: OFF/ [COPY] button: ON ([FAX] LED: OFF/ [COPY] LED: ON) Contents Highlighted display Normal display Digital key Button Items to check e.g. e.g. Dongle (for Printer/Scanner kit (GM-2260) Connectable Not connectable Connected Dongle (for Printer kit (GM-1240) Connectable Not connectable Connected Dongle (for Scanner kit (GM-4240)
Page 931
Output check (test mode 03) Code Function Procedure Main motor ON (operational without developer unit) Toner motor ON (normal rotation) Polygonal motor ON (600 dpi) Registration clutch ON PFP motor ON ADU motor ON (low speed) Laser ON Exit motor ON (normal rotation) Exit motor ON (reverse rotation) LCF motor ON Reverse motor ON (normal rotation) * e-STUDIO356/456 only...
Page 932
Scan motor ON (Automatically stops at limit position; speed can be changed with the [ZOOM] button Scanner exposure lamp ON/OFF LCF tray-up motor (up/down) PFP upper drawer tray-up motor ON (tray up) PFP lower drawer tray-up motor ON (tray up) RADF feed motor ON/OFF (normal rotation) RADF feed motor ON/OFF (reverse rotation) RADF read motor ON/OFF (normal rotation)
Page 933
Test print mode (test mode 04) Code Types of test pattern Remarks Remarks Output from Secondary scanning direction 17 gradation Error diffusion steps Pattern width: 2 dots, Grid pattern Pitch: 10 mm...
Page 934
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Process Developer Automatic adjustment 2000 Fuser heater ON As the value increases, the sensor output increases t mode of auto-toner sensor correspondingly.
Page 935
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Process Transfer Transfer cleaning bias 2084 Negative 0~255 When the high-voltage transformer is replaced, the t mode adjustment transfer cleaning bias needs to be adjusted with this code.
Page 936
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Scanner Scanner Distortion mode 3033 Distortion mode Moves carriages to the adjusting position. t mode Adjustmen Scanner Scanner Shading position 3034 Original glass 92~165...
Page 937
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Scanner Scanner Data transfer of 3203 SLG board -> SYS SYS Transfers the characteristic values of the scanner t mode characteristic value board (shading correction factor / RGB color correction /...
Page 938
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Image Adj. of drawer 4018 2nd drawer 0~255 When the value increases by "1", the image shifts t mode sideways deviation toward the front side by 0.0423 mm.
Page 939
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Image 4055 Left margin 0~255 When the value increases by "1", the blank area t mode adjustment(blank area becomes wider by approx.
Page 940
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Image 4064 Right margin 0~255 When the value increases by "1", the blank area t mode adjustment (blank becomes wider by approx.
Page 941
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4101 Plain paper; Middle Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 942
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4104 Thick paper1; Long Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 943
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4105 Thick paper2; Short Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 944
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4107 OHP film; Middle size 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 945
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning PFP lower drawer 4109 Plain paper; Long size Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 946
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning T-LCF 4111 Plain paper Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 947
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4115 Thick paper1; Long Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 948
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4115 Thick paper2; Short Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 949
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning PFP upper drawer 4117 Thick paper1; Middle Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 950
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning T-LCF 4119 Thick paper1 Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 951
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Registration section 4405 Bypass Refer to 0~63 When the value increases by “1”, the aligning amount t mode system/Pa amount adjustment...
Page 952
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Finisher Paper stack folding 4821 LD/A3 -17~17 t mode position adjustment value Adjustmen Printer Finisher Paper stack folding 4821 LG/B4/8K/A4-R/LT- -17~17...
Page 953
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Finisher 4827 Gripper arm exiting -15~15 t mode position adjustment Adjustmen Image Backgroun PPC(black) 7025 0~255 SYS The smaller the adjustment value is, the lighter the t mode Processing d offset...
Page 954
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Sharpness PPC(black) 7059 Presentation 0~255 SYS The larger the value is, the sharper the image becomes. t mode Processing adjustment The smaller the value is, the softer the image becomes...
Page 955
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density PPC(black) Automatic density 7124 Text 0~255 SYS When the value increases, the image becomes darker. t mode Processing adjustment adjustment...
Page 956
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PPC(black) Photo 7192 Medium density 0~255 SYS The larger the value is, the darker the image of the area t mode Processing balance...
Page 957
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Setting PPC(black) Text 7219 Beam level 1/4 0~10 The smaller the value is, the narrower the beam width t mode Processing beam level...
Page 958
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Setting PPC(black) Presentation 7221 Beam level 2/4 0~10 The smaller the value is, the narrower the beam width t mode Processing beam level...
Page 959
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PPC(black) User custom 7276 Medium density 0~255 SYS The larger the value is, the darker the image of the t mode Processing balance...
Page 960
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Range PPC(black) Black/Manual density 7290 Presentation SYS 0: Background peak - Fixed t mode Processing correction adjustment 1: Background peak - Varied adjustment Adjustmen Image...
Page 961
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PRT(black) PCL/Smooth/600dpi 7317 Medium density 0~255 SYS When the value increases, the density in the target area t mode Processing balance...
Page 962
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PRT(black) XPS/Detail/600dpi 7320 Low density 0~255 SYS When the value increases, the density in the target area t mode Processing balance...
Page 963
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Setting Black NW printer Toner saving OFF 7350 Beam level 4/4 0~10 Adjustment of the smudged/faint text. With decreasing t mode Processing beam level...
Page 964
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Setting Black NW printer Toner saving ON/XPS 7353 Beam level 0/4 0~10 The smaller the value is, the narrower the beam width t mode Processing beam level...
Page 965
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Setting Black NW printer Test print 7355 Beam level 1/4 0~10 The smaller the value is, the narrower the beam width t mode Processing beam level...
Page 966
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma Monochrome/600dpi/ PS/text 7360 High density 0-255 SYS Larger the value, the density value increases, and t mode Processing balance Auto...
Page 967
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma Monochrome/600dpi/ XPS/graphics 7367 Medium density 0-255 SYS Larger the value, the density value increases, and t mode Processing balance Auto...
Page 968
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Range Range correction Black/Manual density 7423 Photo SYS 0: Background peak - Fixed t mode Processing correction adjustment(Black/Man adjustment 1: Background peak - Varied adjustment...
Page 969
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density SCN(black) Automatic density 7456 Text/Photo 0~255 SYS When the value increases, the image becomes darker. t mode Processing adjustment adjustment...
Page 970
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma SCN(black) Text/Photo 7485 High density 0~255 SYS The larger the value is, the darker the image of the area t mode Processing balance...
Page 971
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density FAX(black) Automatic density 7543 Photo 0~255 SYS When the value increases, the image becomes darker. t mode Processing adjustment adjustment...
Page 972
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Stroke PS/PDF automatic 600dpi 8239 Minimum stroke width SYS This code is used to change the width of fine line when t mode Processing adjustment...
Page 973
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image SCN (color) 8320 Text SYS Sets the color space format of the output image. t mode Processing conversion 0: sRGB method 1: AppleRGB...
Page 974
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density SCN (color) Manual 8340 Text 0~255 SYS When the value increases, the image becomes darker. t mode Processing adjustment adjustment/Center...
Page 975
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Range SCN (color) Full color/Manual 8362 Printed image SYS 0: Background peak - Fixed t mode Processing correction density adjustment 1: Background peak - Varied adjustment...
Page 976
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Backgroun SCN (color) Automatic density 8386 Printed image 0~255 SYS The larger the value is, the less easily the background t mode Processing d offset...
Page 977
Resolution adjustment SYS 0: 75dpi 1: 100dpi 2: 150dpi 3: 200dpi t mode of SLIM PDF background processing Adjustmen System General 9960 Equipment Refer to SYS 0: Unset t mode information(SRAM) content 1: ES9160 MFP/ES9170 MFP 2: e-STUDIO256SE/306SE/356SE/456SE <Default value>...
Page 978
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser 2002 Fuser unit error status 0~19 0: No error 1: C410 (Once) 2: C410 (consecutively mode counter occurred) 3: C460 4: C430 5: C440 6: C450 7: C440 8: C450 9: C440 10: C470 11: C470 12: C480 13: C490 14: C470 15: C480 16: C490 17: C470 18:...
Page 979
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature drop 2041 The fourth drop Refer to 0~10 This code is valid only when "20" is set to 08-2135. mode setting in ready status content...
Page 980
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser 2075 Pre-running operation Refer to 0: Not controlled 1: 180 times 2: 360 times 3: 540 mode cycle in ready status content times 4: 720 times 5: 900 times 6: 1080 times...
Page 981
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature drop 2133 The first drop 10~60 This code is valid only when "20" is set to 08-2135. mode switching time setting Setting value x 1 min.: from 10 to 60 min.
Page 982
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser 2140 Fuser roller Refer to 0~14 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C mode temperature during content...
Page 983
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature drop 2191 The second drop Refer to 0~10 Setting value x -5°C: from 0°C to -50°C mode setting during content...
Page 984
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature drop 2198 The fourth drop 0~200 Setting value x 5 seconds: from 0 to 1000 seconds mode switching time setting This code is valid only when "20"...
Page 985
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature drop 2201 The second drop Refer to 0~10 Setting value x -5°C: from 0°C to -50°C mode setting during printing content...
Page 986
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature control 2207 Side thermistor Refer to 0~12 0: 130°C 1: 135°C 2: 140°C 3: 145°C 4: 150°C 5: 155°C mode lower limit(OHP film) content...
Page 987
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser Temperature control 2211 Side thermistor Refer to 0~12 0: 130°C 1: 135°C 2: 140°C 3: 145°C 4: 150°C 5: 155°C mode lower limit(Envelope) content...
Page 988
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Fuser 2214 Temperature drop Refer to 0~20 0: None 1: Pattern 1 2: Pattern 2 3: Pattern 3 4: Pattern mode control setting during content...
Page 989
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Process 2848 Life correction Refer to 0~30 Set value x 4 msec. = Drum rotation time mode switching of normal content 0: No correction rotation amount after...
Page 990
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Charger Main charger bias 2926 0~255 Corrects the value of the main charger bias mode correction (Normal) adjustment(05-2040). Setting Process Charger...
Page 991
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Transfer 2930 Thick 2 transfer Refer to 0~255 The output value of the transfer bias at the leading edge mode correction (C) content...
Page 992
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Separation 2934 Separation Refer to 0~255 Corrects the value of the separation transformer DC mode transformer DC content output adjustment (05-2078).
Page 993
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Laser Laser power 2940 0~255 Corrects the value of the laser power adjustment (05- mode correction (FAX) 2250). Setting Process Process...
Page 994
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Process Separation 2966 Thin paper separation Refer to 0~255 <Default value> mode trailing edge output content correction (L) Setting Process Developer 2978...
Page 995
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting Scanner RADF 3021 Set for switchback- SYS This setting is whether the original length is detected or mode mixed size copy not by transporting without scanning in reverse when A4-R/FOLIO paper or LT-R/LG paper is detected in a mixed-size copying.
Page 996
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System User Card reader 3501 Format information 1 8 digits SYS To access the data in the non-contact IC card, the Key mode interface Information "LLLL"...
Page 997
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System General 3619 Clearing of service SYS Initializes the service history list file. mode history list file Setting System General 3623 Job filtering setting for...
Page 998
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System Network 3706 PDC (Primary Domain UTY Up to 128 letters mode Controller) name 3 for user authentication Setting System Network 3707...
Page 999
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System Network 3730 ATalk PS active 1~16 mode Connection Setting System Network 3731 Raw TCP max 1~16 mode Connection Setting System Network...
Page 1000
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System Network IPv6 3768 Switching IP(IPv6) NIC IP(IPv6) Address Acquisition setting is switched. mode Address Acquisition 1: Manual 2: Stateless 3: Stateful Setting System...
Page 1001
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Setting System General 3803 USB media direct SYS Sets the USB media direct printing function.0: mode printing function Disabled1: Enabled setting Setting System...