Siemens SINAMICS G120XA Operating Instructions Manual page 896

Index
CI: Technology controller output scaling
p2296[0...n], 618
CI: Technology controller precontrol signal
p2289[0...n], 617
CI: Technology controller setpoint 1
p2253[0...n], 611
CI: Technology controller setpoint 2
p2254[0...n], 612
CI: Technology controller Tn adaptation input value
signal source
p2317, 622
CI: Torque limit lower
p1523[0...n], 525
CI: Torque limit lower scaling without offset
p1554[0...n], 528
CI: Torque limit upper
p1522[0...n], 524
CI: Torque limit upper scaling without offset
p1552[0...n], 528
Closed-loop cascade control configuration
p2371, 627
Closed-loop cascade control enable
p2370[0...n], 626
Closed-loop cascade control holding time switch-in
speed
p2385, 631
Closed-loop cascade control holding time switch-out
speed
p2387, 632
Closed-loop cascade control interlocking time
p2377, 629
Closed-loop cascade control max time for continuous
operation
p2381, 630
Closed-loop cascade control mode motor selection
p2372, 627
Closed-loop cascade control motor switch-off delay
p2386, 631
Closed-loop cascade control motor switch-on delay
p2384, 631
Closed-loop cascade control operating hours
p2380[0...2], 630
Closed-loop cascade control operating time limit
p2382, 630
Closed-loop cascade control overcontrol threshold
p2376, 629
Closed-loop cascade control switch-in delay
p2374, 628
Closed-loop cascade control switch-in threshold
p2373, 628
894
Closed-loop cascade control switch-in/switch-out
speed
p2378, 629
Closed-loop cascade control switch-out delay
p2375, 629
Closed-loop cascade control switch-out sequence
p2383, 631
CO/BO: 2/3 wire control control word
r3333.0...3, 648
CO/BO: Bypass control/status word
r1261.0...11, 502
CO/BO: Closed-loop cascade control status word
r2379.0...7, 630
CO/BO: Command Data Set CDS effective
r0050.0...1, 364
CO/BO: Command Data Set CDS selected
r0836.0...1, 447
CO/BO: Compound braking/DC quantity control
status word
r3859.0...1, 653
CO/BO: Control word 1
r0054.0...15, 367
CO/BO: Control word faults/alarms
r2138.7...15, 587
CO/BO: Control word sequence control
r0898.0...10, 454
CO/BO: Control word setpoint channel
r1198.0...15, 488
CO/BO: CU digital inputs status
r0722.0...12, 426
CO/BO: CU digital inputs status inverted
r0723.0...12, 427
CO/BO: Data set changeover status word
r0835.2...8, 447
CO/BO: DC braking status word
r1239.8...13, 497
CO/BO: Drive coupling status word/control word
r0863.0...1, 453
CO/BO: Drive Data Set DDS effective
r0051.0...1, 364
CO/BO: Drive Data Set DDS selected
r0837.0...1, 448
CO/BO: ESM status word
r3889.0...10, 655
CO/BO: Extented setpoint channel selection output
r29640.0...18, 720
CO/BO: Faults/alarms trigger word
r2129.0...15, 584
CO/BO: Free tec_ctrl 0 status word
r11049.0...11, 686
CO/BO: Free tec_ctrl 1 status word
r11149.0...11, 693
Operating Instructions, 03/2019, FW V1.0, A5E44751205B AB
SINAMICS G120XA converter