Table of Contents
Advertisement
Index
N01004 (F, A), 754
N01101 (A), 765
N30800 (F), 822
Ambient temperature, 307, 308
Analog input, 81
Function, 139
Analog output, 81
Function, 145
Application class
p0096, 374, 375
Application example, 131, 145, 166, 236, 237
Application example, 138, 142
Automatic calculation motor/control parameters
p0340[0...n], 398
Automatic restart, 320
Automatic restart delay time start attempts
p1212, 493
Automatic restart faults not active
p1206[0...9], 491
Automatic restart mode
p1210, 491
Automatic restart monitoring time
p1213[0...1], 493
Automatic restart start attempts
p1211, 492
B
Bearing code number selection
p0531[0...n], 413
Bearing maximum speed
p0532[0...n], 413
Bearing version selection
p0530[0...n], 412
BF (Bus Fault), 744, 745
BI: 1st acknowledge faults
p2103[0...n], 577
BI: 2/3 wire control command 1
p3330[0...n], 647
BI: 2/3 wire control command 2
p3331[0...n], 648
BI: 2/3 wire control command 3
p3332[0...n], 648
BI: 2nd acknowledge faults
p2104[0...n], 577
BI: 3rd acknowledge faults
p2105[0...n], 578
BI: Active STW1 in the BOP/IOP manual mode
p8542[0...15], 680
BI: Binector-connector converter status word 1
p2080[0...15], 567
890
BI: Binector-connector converter status word 2
p2081[0...15], 568
BI: Binector-connector converter status word 3
p2082[0...15], 569
BI: Binector-connector converter status word 4
p2083[0...15], 569
BI: Binector-connector converter status word 5
p2084[0...15], 570
BI: Bypass control command
p1266, 503
BI: Bypass switch feedback signal
p1269[0...1], 504
BI: Close main contactor
p0870, 454
BI: Command data set selection CDS bit 0
p0810, 445
BI: Command data set selection CDS bit 1
p0811, 445
BI: Continue ramp-function generator/freeze ramp-
function generator
p1141[0...n], 486
BI: Control by PLC/no control by PLC
p0854[0...n], 451
BI: CU analog outputs invert signal source
p0782[0...2], 439
BI: CU signal source for terminal DO 0
p0730, 428
BI: CU signal source for terminal DO 1
p0731, 428
BI: CU signal source for terminal DO 2
p0732, 429
BI: CU signal source for terminal DO 3
p0733, 430
BI: DC braking activation
p1230[0...n], 495
BI: Deragging enable
p29591[0...n], 714
BI: Drive Data Set selection DDS bit 0
p0820[0...n], 446
BI: Drive Data Set selection DDS bit 1
p0821[0...n], 446
BI: Dual ramp enable
p29580[0...n], 714
BI: Enable energy usage display
p0043, 361
BI: Enable operation/inhibit operation
p0852[0...n], 451
BI: Enable ramp-function generator/inhibit ramp-
function generator
p1140[0...n], 486
BI: Enable setpoint/inhibit setpoint
p1142[0...n], 487
Operating Instructions, 03/2019, FW V1.0, A5E44751205B AB
SINAMICS G120XA converter
Advertisement
Table of Contents
