Mitsubishi Electric M800 Series Manual page 594

M800/M80/E80/C80 Series Alarm/Parameter Manual
16 Machine Parameters
#13543 sptc37
Specify the spindle speed at which a changeover to the 7th step's acceleration/deceleration time constant is
made when the 3rd step gear is selected.
---Setting range---
0 to 99999(r/min)
#13544 spdiv31
Time constant magnification for changeover speed 1 (Gear: 10)
Specify the acceleration/deceleration time constant to be used in a range of the spindle-mode servo control/
spindle synchronization multi-step acceleration/deceleration changeover speed 1 (sptc31) to the spindle
sync multi-step acceleration/deceleration changeover speed 2 (sptc32) when the 3rd step gear is selected.
Set this as a magnification with respect to the spindle-mode servo control/spindle synchronization accelera-
tion/deceleration time constant (spt3).
---Setting range---
0 to 127
#13545 spdiv32
Time constant magnification for changeover speed 2 (Gear: 10)
Specify the acceleration/deceleration time constant to be used in a range of the spindle-mode servo control/
spindle synchronization multi-step acceleration/deceleration changeover speed 2 (sptc32) to the spindle
sync multi-step acceleration/deceleration changeover speed 3 (sptc33) when the 3rd step gear is selected.
Set this as a magnification with respect to the spindle-mode servo control/spindle synchronization accelera-
tion/deceleration time constant (spt3).
---Setting range---
0 to 127
#13546 spdiv33
Time constant magnification for changeover speed 3 (Gear: 10)
Specify the acceleration/deceleration time constant to be used in a range of the spindle-mode servo control/
spindle synchronization multi-step acceleration/deceleration changeover speed 3 (sptc33) to the spindle
sync multi-step acceleration/deceleration changeover speed 4 (sptc34) when the 3rd step gear is selected.
Set this as a magnification with respect to the spindle-mode servo control/spindle synchronization accelera-
tion/deceleration time constant (spt3).
---Setting range---
0 to 127
#13547 spdiv34
Time constant magnification for changeover speed 4 (Gear: 10)
Specify the acceleration/deceleration time constant to be used in a range of the spindle-mode servo control/
spindle synchronization multi-step acceleration/deceleration changeover speed 4 (sptc34) to the spindle
sync multi-step acceleration/deceleration changeover speed 5 (sptc35) when the 3rd step gear is selected.
Set this as a magnification with respect to the spindle-mode servo control/spindle synchronization accelera-
tion/deceleration time constant (spt3).
---Setting range---
0 to 127
#13548 spdiv35
Time constant magnification for changeover speed 5 (Gear: 10)
Specify the acceleration/deceleration time constant to be used in a range of the spindle-mode servo control/
spindle synchronization multi-step acceleration/deceleration changeover speed 5 (sptc35) to the spindle
sync multi-step acceleration/deceleration changeover speed 6 (sptc36) when the 3rd step gear is selected.
Set this as a magnification with respect to the spindle-mode servo control/spindle synchronization accelera-
tion/deceleration time constant (spt3).
---Setting range---
0 to 127
Spindle sync multistep acceleration/deceleration
changeover speed 7 (Gear: 10)
Time constant magnification for changeover speed 1
(Gear: 10)
Time constant magnification for changeover speed 2
(Gear: 10)
Time constant magnification for changeover speed 3
(Gear: 10)
Time constant magnification for changeover speed 4
(Gear: 10)
Time constant magnification for changeover speed 5
(Gear: 10)
577 IB-1501279-H