Texas Instruments SimpleLink CC2620 Technical Reference Manual page 1295

www.ti.com
17.7.7.1 MODCLKEN0 Register (Offset = 0h) [reset = 0h]
MODCLKEN0 is shown in
Module Clock Enable
Clock enable for each module in the AUX domain
For use by the system CPU
The settings in this register are OR'ed with the corresponding settings in MODCLKEN1. This allows the
system CPU and AUX_SCE to request clocks independently. Settings take effect immediately.
31 30
23 22
15 14
7 6
AUX_ADI4 AUX_DDI0_OS
C
R/W-0h R/W-0h
Bit Field
31-8 RESERVED
7 AUX_ADI4
6 AUX_DDI0_OSC
5 TDC
4 ANAIF
3 TIMER
2 AIODIO1
1 AIODIO0
SWCU117C – February 2015 – Revised September 2015
Submit Documentation Feedback
Figure 17-62 and described in
Figure 17-62. MODCLKEN0 Register
29 28
RESERVED
R-0h
21 20
RESERVED
R-0h
13 12
RESERVED
R-0h
5 4
TDC ANAIF
R/W-0h R/W-0h
Table 17-87. MODCLKEN0 Register Field Descriptions
Type Reset
R 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
Copyright © 2015, Texas Instruments Incorporated
AUX – Sensor Controller Registers
Table 17-87.
27 26
19 18
11 10
3 2
TIMER AIODIO1
R/W-0h R/W-0h
Description
Software must not rely on the value of a reserved. Writing any other
value than the reset value may result in undefined behavior.
Enables (1) or disables (0) clock for AUX_ADI4.
0h = System CPU has not requested clock for AUX_ADI4
1h = System CPU has requested clock for AUX_ADI4
Enables (1) or disables (0) clock for AUX_DDI0_OSC.
0h = System CPU has not requested clock for AUX_DDI0_OSC
1h = System CPU has requested clock for AUX_DDI0_OSC
Enables (1) or disables (0) clock for AUX_TDCIF.
Note that the TDC counter and reference clock sources must be
requested separately using TDCCLKCTL and REFCLKCTL,
respectively.
0h = System CPU has not requested clock for TDC
1h = System CPU has requested clock for TDC
Enables (1) or disables (0) clock for AUX_ANAIF.
Note that the ADC internal clock must be requested separately using
ADCCLKCTL.
0h = System CPU has not requested clock for ANAIF
1h = System CPU has requested clock for ANAIF
Enables (1) or disables (0) clock for AUX_TIMER.
0h = System CPU has not requested clock for TIMER
1h = System CPU has requested clock for TIMER
Enables (1) or disables (0) clock for AUX_AIODIO1.
0h = System CPU has not requested clock for AIODIO1
1h = System CPU has requested clock for AIODIO1
Enables (1) or disables (0) clock for AUX_AIODIO0.
0h = System CPU has not requested clock for AIODIO0
1h = System CPU has requested clock for AIODIO0
AUX – Sensor Controller with Digital and Analog Peripherals
25 24
17 16
9 8
1 0
AIODIO0 SMPH
R/W-0h R/W-0h
1295