Texas Instruments SimpleLink CC2620 Technical Reference Manual page 1612

Radio Registers
23.8.2.3 RFHWIFG Register (Offset = 8h) [reset = 0h]
RFHWIFG is shown in
Interrupt Flags From RF Hardware Modules
31 30
23 22
RESERVED
15 14
RATCH3 RATCH2
R/W-0h R/W-0h
7 6
RESERVED TRCTK
R/W-0h R/W-0h
Bit Field
31-20 RESERVED
19 RATCH7
18 RATCH6
17 RATCH5
16 RATCH4
15 RATCH3
14 RATCH2
13 RATCH1
12 RATCH0
11 RFESOFT2
10 RFESOFT1
9 RFESOFT0
8 RFEDONE
7 RESERVED
6 TRCTK
1612
Radio
Figure 23-23 and described in
Figure 23-23. RFHWIFG Register
29 28
21 20
R-0h
13 12
RATCH1 RATCH0
R/W-0h R/W-0h
5 4
MDMSOFT MDMOUT
R/W-0h R/W-0h
Table 23-167. RFHWIFG Register Field Descriptions
Type Reset
R 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
R/W 0h
Copyright © 2015, Texas Instruments Incorporated
Table 23-167.
27
RESERVED
R-0h
19
RATCH7 RATCH6
R/W-0h R/W-0h
11
RFESOFT2 RFESOFT1
R/W-0h R/W-0h
3
MDMIN MDMDONE
R/W-0h R/W-0h
Description
Software must not rely on the value of a reserved. Writing any other
value than the reset value may result in undefined behavior.
Radio timer channel 7 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 6 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 5 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 4 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 3 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 2 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 1 interrupt flag. Write zero to clear flag. Write to
one has no effect.
Radio timer channel 0 interrupt flag. Write zero to clear flag. Write to
one has no effect.
RF engine software defined interrupt 2 flag. Write zero to clear flag.
Write to one has no effect.
RF engine software defined interrupt 1 flag. Write zero to clear flag.
Write to one has no effect.
RF engine software defined interrupt 0 flag. Write zero to clear flag.
Write to one has no effect.
RF engine command done interrupt flag. Write zero to clear flag.
Write to one has no effect.
Software must not rely on the value of a reserved. Writing any other
value than the reset value may result in undefined behavior.
Debug tracer system tick interrupt flag. Write zero to clear flag. Write
to one has no effect.
SWCU117C – February 2015 – Revised September 2015
26 25
18 17
RATCH5
R/W-0h
10 9
RFESOFT0 RFEDONE
R/W-0h
2 1
FSCA RESERVED
R/W-0h
Submit Documentation Feedback
www.ti.com
24
16
RATCH4
R/W-0h
8
R/W-0h
0
R/W-0h