Lnstallation - Acura Integra 1998 Service Manual

lnstallation
CAUTION: Th€ vehiclo should bs on the ground b€fore any bolts or nuis connectod to rubber mounis or bushings aro
tightened.
NOTE:
. Wipe off thedirt,oil or gr€ase on the threads before tightening the fasteners.
. The right and left damper forks are not interchangeable. The left damper fork is ma.ked with "VL" while the righr
damoer fork is marked with "VR".
. The right and left upper arms are not interchangeable. The left upper arm is marked with "SRZ-L" while the right arm is
marked with "SRZ-R".
.
Before tightening the upper and lower mounting nuts on the stabilizer link, adjust the location ot the link with the sus-
pension under vehicle load.
. When installing the radius arm washers, the "FR" mark faces the front ofthe car.
. After installing the suspension a rm, check the front wheel alignmentand adjust if necesssry (see page 18-4).
SELF-LOCKING NUT
12 x 1.25 nn
64 N.m {6,5 kg{.m, 47
Replace.
STABILIZER BAR
Align the stabilazer mark
w i t h e n d o f s t a b i l i z e r
BOLT
STABILIZER EUSHING
SELF.LOCKING NUT
I x 1.25 mm
22 N.m 12.2 kgt m, 16 lbf.ft)
Replace.
FLANGE BOLT
12 x 1.25 mm
FLANGE NUT
I x 1.25 mm
22 N.m {2.2 kgt m. 16 lbf.ft}
BADIUS ARM WASHER B
{SMALL I.D.)
\
64 N.m {6.5 kg{.m, 47 lbt.ft) .
SELF.LOCKING NUT
1 4 x 1 . 5 m m
83 N.m {8.5 kgI.m, 61 lbl.ftl
Replace.
RAOIUS ARM WASHER A
{LARGE I.O.I
.@]
SILICONE GREASE
RUBBER BUSHING
FLANGE BOLTS
1 4 x 1 . 5 m m
89 N.m {9.1 kgf.m, 66 lbtft)
RS, LS Modebi
SELF.LOCKING NUT
8 x 1.25 mm
22 N.m (2.2 kg,f.m. 16lbtftl
SELF.LOCKING NUT
I x I .25 mm
22 N m {2.2 kgt'm, 15 lbf.ft)
Replace.
1 4 x 1 . 5 m m
8 9 N m { 9 . 1 k g f m , 6 6 l b l f t )
SELF-LOC(ING NUT
l0 x 1.25 mm
29 N.m 13.0 kgf.m,22 lbtftl
Replace.
H o l d t h e b a l l j o i n t p i n u s i n g a
hex wrench, and tighten the self-
locking nut.
FLANGE BOLT
10 x 1.25 mm
43 N.m {4.4 kgl.m, 32lbf.ft}
SELF-LOCKING NUT
12 x 1.25 mm
64 N.m {6.5 kgf.m, 47 lbtftl
Replace.
S E L F - L O C K I N G N U T 8 x 1 . 2 5 m m
22 N.m {2.2 kgI m, 16lbf.ft)
STABILIZER END RUBBER BUSHINGS
Note the direction
of the bushinas.
R e p l a c e .
B e f o r e t i g h t e n i n g t h e s e l f l o c k i n g n u t s , p o s i t i o n t h e b a l l j o i n t p i n
a t t h e c e n t e r o f t h e r a n g e i n w h i c h t h e p i n c a n b e m o v e d w i t h t h e
s u s p e n s i o n u n d e r v e h i c l e l o a d .
MARK
SILICONE GREASE
1A-21