Front Suspension; Torque Specifications - Acura Integra 1998 Service Manual

Front Suspension
Torque Specifications
CAUTION:
. Replacc the selt-locking nuts after removal.
. The vehicle should be on the ground before any bolts or nuls connected to rubber mounts or bushings are tightoned.
o Torque thc castle nut to the lower torque spocitication, then tighten it only far onough to align the slot with the pin
hole. Do not align the nut bv loosening.
NOTE: Wipe offthegrease before tightening the nutatthe ball joint.
SELF-LOCKING NUT
1 2 x 1 . 2 5 m m
64 N.m (6.s ksf.m, 47 lbfft)
FLANGE NUT
1 0 x 1 . 2 5 m m
49 N.m {5.0 kgtm.36 lbt.frl
SELF.LOCKING NUT
10 x 1.25 mm
29 N.m {3.0 kgtm,22 lbl.ft)
Replace.
CALIPER BRACKET MOUNTING BOLT
12 x 1.25 mm
108 N.m {11.0 kgl.m,80lbl.ftl
SELF-LOCKING NUT
1 4 x 1 . 5 m m
83 N.m {8.5 kgf.m, 61 lbf.ft}
CASTLE NUT
1 2 x 1 . 2 5 m m
39 - 47 N.m {4.0 - 4.8 kgtm, 29 - 35 lbf.ft}
-'-
FLANGE BOLTS
1 4 x 1 . 5 m m
89 N.m (9.1 kgl m, 56lblft)
FLANGE NUT
8 x 1.25 mm
22 N.m (2.2 kgf.m, 16lbtftl
8 mm BOLT
2 2 N . m { 2 . 2 k s n m , 1 6 l b { f t }
R e p l a c e .
FLANGE BOLT
1 4 x 1 . 5 m m
89 N m 19.1 kgt.m,66 lbl.ftl
FLANGE EOLT
l 0 x l 2 5 m m
4i, N.m (4.4 kgl.m, 32 lbf.ft)
FLANGE BOLT
12x 1.25 mm
64 N.m (6.5 kgtm, iU lbfftl
SELF-I-OCKING NUTS
22 N.m {2.2 kgtm, 16lbtftl
Replace.
NUT
10 x 1.25 mm
43 N.m {4.4 kgt.m,32 lbf.ftl
SPINDLE NUT
22 x 1.5 nm
181 N.m {18.5 kgtm. 134 tbl.ft)
Replace.
NOTEi After tightening, use a drifl to
stake the spindle nut shoulder against
the dfiveshaft,
29 N.m {3.0 kgf.m, 22lbtttl
B e p l a c e .
GS, GSR, Type R
Models:
SELF.LOCKING NUT
10 x 1.25 mm
SELF-LOCKING NUT
I x 1.25 mm
22 N.m (2.2 ksf.m, 16lbl.ftl
Replace-
CASTLE NUT
12 x '1.25 mm
49 - 59 N.m (5.0 - 6.0 kgt m, 36 - 43 tbt.ftl
S E L F . L O C K I N G N U T
12x 1-25 tnrn
64 N.m 16.5 kgl.m, 47 lbf.ftl
R e p l a c e .
-
--.."
t,..
0 - . .
1 8 - 8