Acura Integra 1998 Service Manual page 405

I
\
72 mm Thrust Shim
Part Number
Thickness
2 3 9 3 1 - P 2 1 - 0 0 0
0.60 mm (0.0236 in)
B 2 3 9 3 2 - P 2 1 - 0 0 0
0.63 mm (0.0248 in)
c
23933 - P21 -000
0.66 mm (0.0260 in)
D 23934 P21 000 0.69 mm (0.0272 in)
E
23935 P21 - 000
0 . 7 2 m m ( 0 . 0 2 8 3 I n )
23936 P21 000
0.75 mm (0.0295 n)
G
23937 - P21 000
0.78 mm 10.0307 n)
23938 - P21 -000
0.81 mm 10.0319
n )
23939 P21 - 000
0.84 mm {0.0331 n)
J 23940 P21 000
0.87 mm (0.0343 in)
K
23941 - P21 -000
0.90 mm (0.0354 in)
L
23942 - P21 - 000
0.93 mm (0.0366 in)
M
23943 - P21 -000
0.96 mm (0.0378 in)
N
23944-P21 -000
0.99 mm {0.0390 in)
o
23945 - P21 -000
1.02 mm (0.0402 in)
23946 P2r - 000
1 . 0 5 m m ( 0 . 0 4 1 3 i n )
o
23947 P2r - 000
1.08 mm (0.0425 in)
23948 P21 - 000
1 . 1 1 m m ( 0 . 0 4 3 7 ; n i
23949 P21 - 000
1 . 1 4 m m ( 0 . 0 4 4 9 i n i
T
2 3 9 5 0 - P 2 1 - 0 0 0
1 . 1 7 m m ( 0 . 0 4 6 1 i n )
23951 - P21 -000
1.20 mm (0.0472 in)
23952 P21 - O00
1.23 mm (0.0484 in)
23953 P21 - 000
1 . 2 6 m m ( 0 . 0 4 9 6 ' n )
23954 - P21 000
'1.29 mm (0.0508
in)
23955, P21 000 1 . 3 2 m m ( 0 . 0 5 2 0 i n )
z
23956 P21 - 000
1.35 mm (0.0531 in)
23957 P2r - 000
1 . 3 8 m m ( 0 . 0 5 4 3 i n )
AB
23958 P21 - 000
1 . 4 1 m m ( 0 . 0 5 5 5 i n )
AC
2 3 9 5 9 - P 2 1 - 0 0 0
1.44 mm (0.0567 in)
AD
23960 P2r 000
1 . 4 7 m m ( 0 . 0 5 7 9 i n )
AE
23961 - P21 000
L 5 0 m m 1 0 . 0 5 9 1 r n ,
23962 - P21 000
1.53 mm {0.0602 in)
AG
23963, P21 000
1 . 5 6 m m ( 0 . 0 6 1 4 i n )
AH
23964 P21 000
1.59 mm (0.0626 jn)
23965 P21 000 1.62 mm (0.0638 in)
23966 - P21 000
1.65 mm (0.0650 in)
AK 2 3 9 6 7 - P 2 t - 0 0 0 1.68 mm (0.0661 In)
2 3 9 6 8 - P 2 1 - 0 0 0
1.71 mm (0.0673 in)
23969 P21 - 000
1.74 mm (0.0685 in)
AN
23970 P21 - 000
1.77 mm {0.0697 in)
AO
23971 P21 - 000
'l -80
mm {0.0709 in)
1 .
72 mm THRUST
TRANSMISSION
HoustNG --'-.rft=>t
o
Check the thrust clearance in the manner described
oerow.
N O T E : C h e c k t h e m e a s u r e m e n t a t n o r m a l r o o m
temperature.
a . I n s t a l l t h e t h r u s t s h i m s e l e c t e d a n d o i l g u i d e
plate in the transmission housing.
OIL GUIOE PLATE
b .
f.
NOTE:
. Clean the spring washer, washer and thrust shim
throughly before installation,
. I n s t a l l t h e s p r i n g w a s h e r , w a s h e r a n d t h r u s t
shim properly.
-
--
/wAsHER
(€>P-
X
-spnrruc wlssen
a a.7l=\-\-
I n s t a l l t h e m a i n s h a f t i n t h e c l u t c h h o u s i n g .
Place the transmission housing over the main-
shaft and onto the clutch housing.
T i g h t e n t h e c l u t c h a n d t r a n s m i s s i o n h o u s i n g s
with several I mm bolts.
NOTE: lt is not necessary to use sealing agent
between the housings.
8 x 1 . 2 5 m m
27 N.m (2.8 kgf.m, 20 lbt.ft)
Tap the mainshaft with a plastic hammer.
c .
o .
t: o
I n s t a l l t h e s p r i n g
b a l l b e a r i n g .
w a s h e r a n d w a s h e r o n t h e
(cont'd)
il
1 3 - 3 9