Acura Integra 1998 Service Manual page 605

7 . li the clearance is not within the standard, select a
new 80 mm shim from the tollowing table.
Standard: 0-0.10 mm {0.004 in)
80 mm Shim
NOTE: lf the clearance measured in step 6 is within
the standard, it is not necessary to go to step 9.
)
)
Part Number Thickness
4 1 4 4 1 - P L 3 - B O O
' L o
m m ( O . O 3 9 4 i n )
I 41442-PL3-BOO
1 , 1 m m ( O . O 4 3 3 i n )
c
4 1 4 4 3 - P L 3 - B 0 0 1.2 mm lO.O47 2 inl
D
4't 444- PL3 - BOO
1 . 3 m m ( O . O 5 1 2 i n )
4 1 4 4 5 - P L 3 - 8 0 0
1 . 4 m m ( O . 0 5 5 1 i n )
4 1 4 4 6 - P L 3 - B O O
1 . 5 m m ( O . O 5 9 l i n l
41447 -PL3-BOO
1 . 6 m m ( 0 . 0 6 3 0 i n )
H
4 1 4 4 8 - P L 3 - B O 0
1 . 7 m m ( 0 . 0 6 6 9 i n )
J 4 1 4 4 9 - P L 3 - 8 0 0
1 . 8 m m ( O . O 7 O 9 i n l
K
4 1 4 5 0 - P L 3 - B O O 1 . O S m m { O . O 4 1 3 i n )
4 1 4 5 1 - P L 3 - B O O 1 . 1 5 m m { O . O 4 5 3 i n )
M
4 ' 1 4 5 2 - P L 3 - B O 0 1 . 2 5 m m ( 0 . 0 4 9 2 i n )
N
4 1 4 5 3 - P L 3 - 8 0 0
' 1 . 3 5
m m ( 0 . 0 5 3 2 i n )
P 4 1 4 5 4 - P L 3 - 8 0 0
1 . 4 5 m m ( O . 0 5 7 1 i n )
o
4 1 4 5 5 - P L 3 - B O O 1 . 5 5 m m { O . 0 6 1 O i n )
R
4 1 4 5 6 - P L 3 - B O O 1 . 6 5 m m ( 0 . 0 6 5 0 i n )
4 1 4 5 7 - P L 3 - B O O
1 . 7 5 m m ( 0 . 0 6 8 9 i n )
T 4 1 4 4 1 - P 2 1 - O O O 1 . 8 5 m m ( 0 . 0 7 2 8 i n )
U
4 1 4 4 2 - P 2 ' t - O O O
1 . 9 0 m m ( 0 . 0 7 4 8 i n )
4 1 4 4 3 - P 2 1 - 0 0 0
1 . 9 5 m m ( 0 . 0 7 6 8 i n )
8 .
9 .
Remove the bolts and transmission housing.
Replace the 80 mm shim selected in step 7, then
recheck the clearance.
Reassemble the transmission and install the trans-
mission housing (see section 13).
1 0 .
15-7