ABB RES670 Technical Manual page 505

1MRK 511 408-UUS A
Name Values (Range)
FrDbRepInt 1 - 100000
FrZeroDb 0 - 100000
FrHiHiLim 0.000 - 100.000
FrHiLim 0.000 - 100.000
FrLowLim 0.000 - 100.000
FrLowLowLim 0.000 - 100.000
FrLimHyst 0.000 - 100.000
VGenZeroDb 1 - 100
IGenZeroDb 1 - 100
VMagComp5 -10.000 - 10.000
VMagComp30 -10.000 - 10.000
VMagComp100 -10.000 - 10.000
IMagComp5 -10.000 - 10.000
IMagComp30 -10.000 - 10.000
IMagComp100 -10.000 - 10.000
IAngComp5 -10.000 - 10.000
IAngComp30 -10.000 - 10.000
IAngComp100 -10.000 - 10.000
Table 377: CMMXU Non group settings (basic)
Name Values (Range)
IA_DbRepInt 1 - 100000
Operation Disabled
Enabled
IA_Min 0.0 - 500.0
IA_Max 0.0 - 500.0
GlobalBaseSel 1 - 12
Table continues on next page
Phasor measurement unit RES670 2.2 ANSI
Technical manual
Unit Step Default
Type 1 10
m% 10 100
Hz 0.001 65.000
Hz 0.001 63.000
Hz 0.001 47.000
Hz 0.001 45.000
% 0.001 5.000
%VB 1 5
%IB 1 5
% 0.001 0.000
% 0.001 0.000
% 0.001 0.000
% 0.001 0.000
% 0.001 0.000
% 0.001 0.000
Deg 0.001 0.000
Deg 0.001 0.000
Deg 0.001 0.000
Unit Step Default
Type 1 10
- - Disabled
%IB 0.1 50.0
%IB 0.1 200.0
- 1 1
Section 16
Monitoring
Description
Cycl: Report interval (s), Db: In 0,001% of
range, Int Db: In 0,001%s
Magnitude zero point clamping in 0,001% of
range
High High limit (physical value)
High limit (physical value)
Low limit (physical value)
Low Low limit (physical value)
Hysteresis value in % of range, common for
all limits
Zero point clamping in % of VBase
Zero point clamping in % of IBase
Magnitude factor to calibrate voltage at 5% of
Vn
Magnitude factor to calibrate voltage at 30%
of Vn
Magnitude factor to calibrate voltage at 100%
of Vn
Magnitude factor to calibrate current at 5% of
In
Magnitude factor to calibrate current at 30%
of In
Magnitude factor to calibrate current at 100%
of In
Angle calibration for current at 5% of In
Angle calibration for current at 30% of In
Angle calibration for current at 100% of In
Description
Cycl: Report interval (s), Db: In 0,001% of
range, Int Db: In 0,001%s
Disbled/Enabled operation
Minimum value in % of IBase
Maximum value in % of IBase
Selection of one of the Global Base Value
groups
PID-6735-SETTINGS v3
499