Siemens SINAMICS G120 List Manual page 702

2 Parameters
2.3 Command and drive data sets - overview
p2208[0...n]
p2209[0...n]
p2210[0...n]
p2211[0...n]
p2212[0...n]
p2213[0...n]
p2214[0...n]
p2215[0...n]
p2216[0...n]
p2230[0...n]
p2237[0...n]
p2238[0...n]
p2240[0...n]
p2247[0...n]
p2248[0...n]
p2502[0...n]
p2503[0...n]
p2504[0...n]
p2505[0...n]
p2506[0...n]
p2519[0...n]
p2533[0...n]
p2534[0...n]
p2535[0...n]
p2536[0...n]
p2538[0...n]
p2539[0...n]
p2546[0...n]
p2567[0...n]
p2634[0...n]
p2720[0...n]
p2721[0...n]
p2722[0...n]
r2723[0...n]
r2724[0...n]
p2900[0...n]
p2901[0...n]
p2930[0...n]
p3231[0...n]
p3233[0...n]
p3315[0...n]
p3316[0...n]
p3320[0...n]
p3321[0...n]
p3322[0...n]
p3323[0...n]
p3324[0...n]
p3325[0...n]
p3326[0...n]
p3327[0...n]
p3328[0...n]
p3329[0...n]
p3820[0...n]
p3821[0...n]
p3822[0...n]
702
CO: Technology controller fixed value 8 / Tec_ctr fix val 8
CO: Technology controller fixed value 9 / Tec_ctr fix val 9
CO: Technology controller fixed value 10 / Tec_ctr fix val 10
CO: Technology controller fixed value 11 / Tec_ctr fix val 11
CO: Technology controller fixed value 12 / Tec_ctr fix val 12
CO: Technology controller fixed value 13 / Tec_ctr fix val 13
CO: Technology controller fixed value 14 / Tec_ctr fix val 14
CO: Technology controller fixed value 15 / Tec_ctr fix val 15
Technology controller fixed value selection method / Tec_ctr FixVal sel
Technology controller motorized potentiometer configuration / Tec_ctr mop config
Technology controller motorized potentiometer maximum value / Tec_ctrl mop max
Technology controller motorized potentiometer minimum value / Tec_ctrl mop min
Technology controller motorized potentiometer starting value / Tec_ctrl mop start
Technology controller motorized potentiometer ramp-up time / Tec_ctr mop t_r-up
Technology controller motorized potentiometer ramp-down time / Tec_ctrMop t_rdown
LR encoder assignment / Encoder assignment
LR length unit LU per 10 mm / LU per 10 mm
LR motor/load motor revolutions / Mot/load motor rev
LR motor/load load revolutions / Mot/load load rev
LR length unit LU per load revolution / LU per load rev
LR position actual value preprocessing config. DDS changeover / s_act config DDS
LR position setpoint filter time constant / s_set_filt T
LR speed precontrol factor / n_prectrl fact
LR speed precontrol balancing filter dead time / n_prectrFlt t_dead
LR speed precontrol symmetrizing filter PT1 / n_prectrl filt PT1
LR proportional gain / Kp
LR integral time / Tn
LR dynamic following error monitoring tolerance / s_delta_monit tol
LR torque precontrol moment of inertia / M_prectr M_inertia
EPOS fixed stop maximum following error / Following err max
Load gear configuration / Load gear config
Load gear rotary absolute encoder revolutions virtual / Abs rot rev
Load gear position tracking tolerance window / Pos track tol
CO: Load gear absolute value / Load gear abs_val
CO: Load gear position difference / Load gear pos diff
CO: Fixed value 1 [%] / Fixed value 1 [%]
CO: Fixed value 2 [%] / Fixed value 2 [%]
CO: Fixed value M [Nm] / Fixed value M [Nm]
Load monitoring speed deviation / Load monit n_dev
Torque actual value filter time constant / M_act_filt T
Efficiency optimization 2 minimum flux limit value / Min flux lim val
Efficiency optimization 2 maximum flux limit value / Max flux lim val
Fluid flow machine power point 1 / Fluid_mach P1
Fluid flow machine speed point 1 / Fluid_mach n1
Fluid flow machine power point 2 / Fluid_mach P2
Fluid flow machine speed point 2 / Fluid_mach n2
Fluid flow machine power point 3 / Fluid_mach P3
Fluid flow machine speed point 3 / Fluid_mach n3
Fluid flow machine power point 4 / Fluid_mach P4
Fluid flow machine speed point 4 / Fluid_mach n4
Fluid flow machine power point 5 / Fluid_mach P5
Fluid flow machine speed point 5 / Fluid_mach n5
Friction characteristic value n0 / Friction n0
Friction characteristic value n1 / Friction n1
Friction characteristic value n2 / Friction n2
SINAMICS G120 CU250S-2 Control Units
List Manual, 09/2017, A5E33842890