Siemens SINAMICS G120 List Manual page 710

2 Parameters
2.4 BICO parameters (connectors/binectors)
p2597
p2604
p2612
p2613
p2614
p2625
p2626
p2627
p2628
p2631
p2633
p2637
p2638
p2639
p2640
p2641
p2647
p2648
p2649
p2650
p2651
p2652
p2653
p2655[0...1]
p2656
p2658
p2659
p2661
p2662
p2663
p2730[0...3]
p2731
p3111[0...n]
p3112[0...n]
p3232[0...n]
p3330[0...n]
p3331[0...n]
p3332[0...n]
p3340[0...n]
p3342[0...n]
p3343[0...n]
p4655[0...2]
p5614
p8542[0...15]
p8558
p8785
p8786
p8787
p9705
p10007
p20030[0...3]
p20034[0...3]
p20038[0...3]
p20042[0...3]
p20046[0...3]
710
BI: EPOS referencing type selection / Ref_typ select
BI: EPOS search for reference start direction / Srch for ref dir
BI: EPOS search for reference reference cam / Ref_cam
BI: EPOS search for reference reversing cam minus / Rev minus
BI: EPOS search for reference reversing cam plus / Rev plus
BI: EPOS traversing block selection bit 0 / Trav_blk sel bit 0
BI: EPOS traversing block selection bit 1 / Trav_blk sel bit 1
BI: EPOS traversing block selection bit 2 / Trav_blk sel bit 2
BI: EPOS traversing block selection bit 3 / Trav_blk sel bit 3
BI: EPOS activate traversing task (0 -> 1) / Trav_task act
BI: EPOS external block change (0 -> 1) / Ext BlckChg (0->1)
BI: EPOS fixed stop reached / Fixed stop reached
BI: EPOS fixed stop outside the monitoring window / Fixed stop outside
BI: EPOS torque limit reached / M_limit reached
BI: EPOS intermediate stop (0 signal) / Intermediate stop
BI: EPOS reject traversing task (0 signal) / Trav_task reject
BI: EPOS direct setpoint input/MDI selection / MDI selection
BI: EPOS direct setpoint input/MDI positioning type / MDI pos_type
BI: EPOS direct setpoint input/MDI transfer type selection / MDI trans_type sel
BI: EPOS direct setpoint input/MDI setpoint acceptance edge / MDI setp_accept
BI: EPOS direct setpoint input/MDI direction selection, positive / MDI dir_sel pos
BI: EPOS direct setpoint input/MDI direction selection negative / MDI dir_sel neg
BI: EPOS direct setpoint input/MDI setting-up selection / MDI setting-up sel
BI: EPOS select tracking mode / Sel tracking mode
BI: EPOS enable basic positioner / EPOS enable
BI: EPOS position actual value valid feedback signal / Pos valid feedback
BI: EPOS referencing active feedback signal / Ref act fdbk
BI: EPOS measured value valid feedback signal / MeasVal valid fdbk
BI: EPOS adjustment value valid feedback signal / Adj val valid FS
BI: EPOS clamping active feedback signal / Clamping active FS
BI: LR pos. actual value preprocessing activate neg. corr. (edge) / ActV_prep neg corr
BI: LR reduce I component / Reduce I comp
BI: External fault 3 enable / Ext fault 3 enab
BI: External fault 3 enable negated / Ext flt 3 enab neg
BI: Load monitoring failure detection / Load_moni fail_det
BI: 2/3 wire control command 1 / 2/3 wire cmd 1
BI: 2/3 wire control command 2 / 2/3 wire cmd 2
BI: 2/3 wire control command 3 / 2/3 wire cmd 3
BI: Limit switch start / Lim switch start
BI: Limit switch plus / Lim switch plus
BI: Limit switch minus / Lim switch minus
BI: XIST1_ERW reset signal source / XIST1_ERW resS_src
BI: Pe set switching-on inhibited signal source / Pe sw-on_inh s_src
BI: Active STW1 in the BOP/IOP manual mode / STW1 act OP
BI: Select IOP manual mode / Sel IOP man mode
BI: CAN status word bit 8 / Status word bit 8
BI: CAN status word bit 14 / Status word bit 14
BI: CAN status word bit 15 / Status word bit 15
BI: SI Motion: Test stop signal source / SI Mtn test stop
BI: SI Motion forced checking procedure F-DO signal source / SI dynF-DI/DOs_src
BI: AND 0 inputs / AND 0 inputs
BI: AND 1 inputs / AND 1 inputs
BI: AND 2 inputs / AND 2 inputs
BI: AND 3 inputs / AND 3 inputs
BI: OR 0 inputs / OR 0 inputs
SINAMICS G120 CU250S-2 Control Units
List Manual, 09/2017, A5E33842890