Connector Outputs (Co) - Siemens SINAMICS G120 List Manual

r20215
r20232
r20233
r20240
r20241
r20262
r20263
r20270
r20271
r20272
r20279
r20280
r20281
r20301
r20305
r20313
r20314
r20315
r20319
r20320
r20321
r20325
r20326
r20330
r20331
r20336
r20341
r20346
r20351
r20356
r20361
2.4.4

Connector outputs (CO)

Product: SINAMICS G120S, Version: 4710100, Language: eng, Type: CO
r0021
r0025
r0026
r0027
r0032
r0034
r0035
r0036
r0037[0...19]
r0039[0...2]
r0042[0...2]
r0060
r0061[0...2]
r0062
r0063[0...2]
r0064
r0066
r0067
r0068[0...1]
SINAMICS G120 CU250S-2 Control Units
List Manual, 09/2017, A5E33842890
BO: BSW 1 output Q / BSW 1 output Q
BO: LIM 0 input quantity at the upper limit QU / LIM 0 QU
BO: LIM 0 input quantity at the lower limit QL / LIM 0 QL
BO: LIM 1 input quantity at the upper limit QU / LIM 1 QU
BO: LIM 1 input quantity at the lower limit QL / LIM 1 QL
BO: INT 0 integrator at the upper limit QU / INT 0 QU
BO: INT 0 integrator at the lower limit QL / INT 0 QL
BO: LVM 0 input quantity above interval QU / LVM 0 X above QU
BO: LVM 0 input quantity within interval QM / LVM 0 X within QM
BO: LVM 0 input quantity below interval QL / LVM 0 X below QL
BO: LVM 1 input quantity above interval QU / LVM 1 X above QU
BO: LVM 1 input quantity within interval QM / LVM 1 X within QM
BO: LVM 1 input quantity below interval QL / LVM 1 X below QL
BO: NOT 4 inverted output / NOT 4 inv output
BO: NOT 5 inverted output / NOT 5 inv output
BO: NCM 0 output QU / NCM 0 output QU
BO: NCM 0 output QE / NCM 0 output QE
BO: NCM 0 output QL / NCM 0 output QL
BO: NCM 1 output QU / NCM 1 output QU
BO: NCM 1 output QE / NCM 1 output QE
BO: NCM 1 output QL / NCM 1 output QL
BO: RSR 2 output Q / RSR 2 output Q
BO: RSR 2 inverted output QN / RSR 2 inv outp QN
BO: DFR 2 output Q / DFR 2 output Q
BO: DFR 2 inverted output QN / DFR 2 inv outp QN
BO: PDE 2 output Q / PDE 2 output Q
BO: PDE 3 output Q / PDE 3 output Q
BO: PDF 2 output Q / PDF 2 output Q
BO: PDF 3 output Q / PDF 3 output Q
BO: MFP 2 output Q / MFP 2 output Q
BO: MFP 3 output Q / MFP 3 output Q
CO: Actual speed smoothed / Actual speed
CO: Output voltage smoothed / U_outp smooth
CO: DC link voltage smoothed / Vdc smooth
CO: Absolute actual current smoothed / Motor current
CO: Active power actual value smoothed / Power
CO: Motor utilization thermal / Mot_util therm
CO: Motor temperature / Mot temp
CO: Power unit overload I2t / PM overload I2t
CO: Power unit temperatures / PM temperatures
CO: Energy display / Energy display
CO: Process energy display / Proc energy disp
CO: Speed setpoint before the setpoint filter / n_set before filt.
CO: Actual speed unsmoothed / n_act unsmoothed
CO: Speed setpoint after the filter / n_set after filter
CO: Actual speed / Actual speed
CO: Speed controller system deviation / n_ctrl sys dev
CO: Output frequency / f_outp
CO: Output current maximum / Current max
CO: Absolute current actual value / I_act abs val
2.4 BICO parameters (connectors/binectors)
2 Parameters
715