Registration Sensor Jam (Duplex) Rap - Xerox VersaLink B7025 Service Manual

077-123 Registration Sensor Jam (Duplex) RAP

BSD-ON: BSD 8.5 Registration
BSD-ON: BSD 10.6 Duplex Transport
077-123 Paper does not actuate the registration sensor in the specified time after the registra-
tion clutch in energized in duplex mode.
Initial Actions
Check the condition of the paper in all trays. Refer to
tions
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
• GP 8 How to Check a Solenoid or Clutch.
Perform the steps that follow:
1. Check for obstructions in the paper path.
2. Check the exit 2 roll and nip rolls,
install new components as necessary.
3. Check the duplex rolls and nip rolls,
install new components as necessary.
4. Enter dC330, code 077-104. Check the registration sensor,
5. Enter dC330, code 077-003. Check the duplex clutch,
6. Enter dC330, code 042-001. Check the drum motor,
7. Enter dC330, code 077-014. Check the exit 2 motor,
8. Check the duplex drive gears and belts,
9. Check the drive assembly, PL 40.10 Item 7
10. If the fault persists, install new components as necessary:
• Drive PWB, PL 1.10 Item 3.
• ESS PWB, PL 3.10 Item 6.
Launch Issue
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
GP 15 Paper and Media Size Specifica-
WARNING
PL 10.22 for foreign substances or wear. Clean or
PL 80.50 for foreign substances or wear. Clean or
PL 80.55 Item 4.
PL 80.50 Item 28.
PL 40.10 Item 2.
PL 10.21 Item 4.
PL 80.50 for wear or damage.
for wear or damage.
077-126, 077-902 Exit 2 Sensor Jam RAP
BSD-ON: BSD 10.5 Fused Paper Exit 2
077-126 After actuating the fuser exit sensor, paper did not actuate the exit 2 sensor within the
specified time.
077-902 The exit 2 sensor detected remaining paper.
Initial Actions
Check the condition of the paper in all trays. Refer to
tions
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
• GP 8 How to Check a Solenoid or Clutch.
Perform the steps that follow:
1. Check for obstructions in the paper path.
2. Check the exit 2 roll and nip rolls,
install new components as necessary.
3. Remove the fuser. Check whether foreign substances or paper is wound around the heat
roll.
4. Enter dC330, code 077-100. Check the exit 2 sensor,
5. Enter dC330, code 077-014. Check the exit 2 motor,
6. Enter dC330, code 077-004. Check the exit gate solenoid,
7. Enter dC330, code 042-003. Check the main motor,
8. Check the exit 2 drive gears,
9. If the fault persists, install new components as necessary:
• Drive PWB, PL 1.10 Item
• ESS PWB, PL 3.10 Item
April 2017
2-479
GP 15 Paper and Media Size Specifica-
WARNING
GP 10. Disconnect the power cord. Electricity can cause
PL 10.22 for foreign substances or wear. Clean or
PL 10.21 Item
PL 10.21 Item
PL 10.22 Item
PL 40.10 Item
PL 10.21 for wear or damage.
3.
6.
Status Indicator RAPs
077-123, 077-126, 077-902
12.
4.
9.
1.