Xerox VersaLink B7025 Service Manual page 641

REPs 1 - Standby Power
REP 1.1 HVPS ................................................................................................................
REP 1.2 Drive PWB ........................................................................................................
REP 1.3 LVPS.................................................................................................................
REP 1.4 LVPS Assembly ................................................................................................
REPs 2 - User Interface
REP 2.1 User Interface Assembly...................................................................................
REPs 3 - Machine Run Control
REP 3.1 ESS PWB .........................................................................................................
REP 3.2 ESS PWB Chassis Assembly ...........................................................................
REP 3.3 SD Card ............................................................................................................
REPs 5 - DADF
REP 5.1 DADF Removal .................................................................................................
REP 5.2 DADF Document Cushion ................................................................................
REP 5.3 DADF Front Cover ............................................................................................
REP 5.4 DADF Rear Cover.............................................................................................
REP 5.5 DADF PWB .......................................................................................................
REP 5.6 Upper Feeder Assembly ...................................................................................
REP 5.7 DADF Feeder Assembly ...................................................................................
REP 5.8 Left Counter Balance ........................................................................................
REP 5.9 Right Counter Balance......................................................................................
REP 5.10 Feed/Nudger Roll Assembly ...........................................................................
REP 5.11 Harness Guide and Wire Harness ..................................................................
REP 5.12 DADF Feed Motor Assembly ..........................................................................
REP 5.13 DADF Drive Belt .............................................................................................
REP 5.14 Document Tray ...............................................................................................
REP 5.15 Retard Chute Assembly..................................................................................
REP 5.16 Invert Chute Assembly....................................................................................
REP 5.17 DADF Takeaway Roll .....................................................................................
REP 5.18 Sensor Bracket Assembly...............................................................................
REP 5.19 Retard Roll Assembly .....................................................................................
REPs 10 - Print Transportation and Fusing
REP 10.1 Exit 1 OCT Assembly......................................................................................
REP 10.2 Exit 2 Roll........................................................................................................
REP 10.3 Fuser Removal ...............................................................................................
REP 10.4 Fuser Fan Duct Assembly ..............................................................................
REPs 12 - Integrated Office Finisher
REP 12.1 Integrated Office Finisher Removal ................................................................
REP 12.2 Paddle Belts....................................................................................................
REP 12.3 Sub Paddle Solenoid ......................................................................................
REP 12.4 Stapler Assembly............................................................................................
REP 12.5 Set Clamp Home Sensor ................................................................................
REP 12.6 Exit Roll Assembly ..........................................................................................
REP 12.7 Nip Roll ...........................................................................................................
Launch Issue
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
4 Repairs and Adjustments
REP 12.8 Finisher Entry Sensor .....................................................................................
REP 12.9 Compiler Exit Sensor ......................................................................................
4-5
REP 12.10 Main Paddle Shaft Assembly ........................................................................
4-6
REP 12.11 Lower Chute Assembly .................................................................................
4-8
REP 12.12 Entry Roll ......................................................................................................
4-9
REP 12.13 Upper Chute Assembly .................................................................................
REP 12.14 Finisher PWB ................................................................................................
4-11
REP 12.15 Stacker Tray Assembly .................................................................................
REP 12.16 Stacker Shaft Assembly................................................................................
REP 12.17 Stacker Motor................................................................................................
4-13
REP 12.18 Stack Sensor 1 and Stack Sensor 2 .............................................................
4-18
REP 12.19 Compiler Assembly .......................................................................................
4-23
REP 12.20 Set Clamp Shaft............................................................................................
REP 12.21 Eject Belt.......................................................................................................
REP 12.22 Eject/Set Clamp Motor Assembly .................................................................
4-25
REP 12.23 Rear Tamper Home Sensor..........................................................................
4-27
REP 12.24 Eject Shaft Assembly ....................................................................................
4-28
REP 12.25 Front /Rear Tamper Motor Assembly............................................................
4-28
REP 12.26 Front Tamper Home Sensor .........................................................................
4-30
REP 12.27 Eject Home Sensor .......................................................................................
4-31
REP 12.28 Stack Height Sensor .....................................................................................
4-32
4-33
REPs 13 - Office Finisher LX
4-34
REP 13.1 H-Transport Assembly ....................................................................................
4-35
REP 13.2 Hole Punch Assembly.....................................................................................
4-36
REP 13.3 H-Transport Belt..............................................................................................
4-39
REP 13.4 H-Transport Motor...........................................................................................
4-40
REP 13.5 Finisher LX Undocking....................................................................................
4-41
REP 13.6 Front Cover .....................................................................................................
4-42
REP 13.7 Rear Upper Cover...........................................................................................
4-43
REP 13.8 Rear Lower Cover...........................................................................................
4-43
REP 13.9 Eject Cover .....................................................................................................
4-47
REP 13.10 Foot Cover ....................................................................................................
4-48
REP 13.11 Stacker Lower Cover ....................................................................................
REP 13.12 Stacker Upper Cover ....................................................................................
REP 13.13 Stack Height Sensors 1 and 2 ......................................................................
4-49
REP 13.14 Sub Paddle Solenoid Assembly....................................................................
4-50
REP 13.15 Stapler Move Motor.......................................................................................
4-52
REP 13.16 Finisher Stapler Assembly ............................................................................
4-53
REP 13.17 Compiler Tray Assembly...............................................................................
REP 13.18 Crease Assembly..........................................................................................
4-55
REP 13.19 Stacker Elevator Motor .................................................................................
4-56
REP 13.20 Stacker Tray..................................................................................................
4-59
REP 13.21 Eject Belt.......................................................................................................
4-60
REP 13.22 Eject Motor Assembly ...................................................................................
4-61
REP 13.23 Finisher PWB ................................................................................................
4-63
REP 13.24 Finisher LVPS ...............................................................................................
4-64
REP 13.25 Eject Motor....................................................................................................
April 2017
4-1
4-64
4-66
4-67
4-69
4-71
4-72
4-73
4-74
4-75
4-78
4-79
4-80
4-82
4-83
4-84
4-86
4-87
4-89
4-90
4-91
4-93
4-95
4-95
4-96
4-97
4-97
4-98
4-99
4-99
4-100
4-102
4-102
4-103
4-103
4-104
4-104
4-106
4-107
4-116
4-117
4-118
4-118
4-119
4-119
4-120
4-121
Repairs and Adjustments