Dadf Simplex/Side 1 Pre Registration Sensor On Jam Rap - Xerox VersaLink B7025 Service Manual

005-122 DADF Simplex/Side 1 Pre Registration Sensor On
Jam RAP
BSD-ON: BSD 5.4 Document Feeding (1 of 2)
005-122 After pre-feed started for the first sheet (DADF feed motor on (CCW)) in simplex and
duplex, the DADF pre registration sensor did not turn on within the specified time.
After pre-feed started for the second sheet onwards (DADF feed motor on (CCW)) in duplex,
the DADF pre registration sensor did not turn on within the specified time.
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
• GP 8 How to Check a Solenoid or Clutch.
Perform the steps that follow:
1. Check for a foreign substance in the document path.
2. Check the surface of the feed roll and nudger roll for foreign substances or wear. Clean or
install new components as necessary,
3. Enter dC330, code 005-206. Check the DADF pre registration sensor,
4. Enter dC330, code 005-062. Check the DADF feed clutch,
5. Enter dC330, code 005-004. Check the DADF feed motor,
6. Check the drive gears, PL 5.35 for wear or damage. Install new components as neces-
sary.
7. If the fault persists, install a new DADF PWB,
Launch Issue
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
WARNING
PL 5.25.
PL 5.70 Item
PL 5.35 Item 2.
PL 5.30 Item 3.
PL 5.10 Item 11.
005-123 DADF Simplex/Side 1 Registration Sensor On Jam
RAP
BSD-ON: BSD 5.6 Document Scan, Invert and Exit Transportation
005-123 The DADF registration sensor does not turn on within the specified time after the
DADF pre registration sensor on.
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
Refer to the procedures that follow as necessary:
• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.
• GP 8 How to Check a Solenoid or Clutch.
Perform the steps that follow:
1. Check for a foreign substance in the document path.
2. Check the surface of the takeaway roll and registration roll for foreign substances or wear.
Clean or install new components as necessary,
3. Enter dC330, code 005-110. Check the DADF registration sensor,
4. Enter dC330, code 005-206. Check the DADF pre registration sensor,
5. Enter dC330, code 005-098. Check the DADF T/A clutch,
3.
6. Enter dC330, code 005-008. Check the DADF feed motor,
7. Check the drive gears, PL 5.35
sary.
8. If the fault persists, install a new DADF PWB,
April 2017
2-37
WARNING
GP 10. Disconnect the power cord. Electricity can cause
PL 5.50.
PL 5.70 Item
PL 5.35 Item
PL 5.30 Item
for wear or damage. Install new components as neces-
PL 5.10 Item 11.
Status Indicator RAPs
005-122, 005-123
3.
PL 5.70 Item 3.
2.
3.