Booklet Folder Home Sensor Fail Rap - Xerox VersaLink B7025 Service Manual

012-243, 012-265 Booklet Folder Home Sensor Fail RAP

BSD-ON: BSD 13.8 Office Finisher LX Folding
012-243 Folder home sensor is not actuated after the lapse of 500ms from motor on while
folder knife is returning to home.
012-265 When the booklet home moves from home position, the folder home sensor did not
turn off within the specified time.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check the folder home sensor, PL 13.40 Item 16
• Check the knife drive mechanism, PL 13.40
Procedure
Enter dC330 code 013-022 and 013-023 alternately to run the folder knife motor.
knife motor runs.
Y N
Check the wiring between P/J8905
J8994 on the booklet PWB and J8985
a loose or damaged connector. The wiring is good.
Y N
Reconnect or repair as necessary.
Install a new booklet folder knife motor,
new booklet PWB, PL 13.70 Item 4.
Enter dC330 code 13-101. Actuate the folder home sensor. The display changes.
Y N
Check the wiring between J8904
open or short circuit, or a loose or damaged connector. The wiring is good.
Y N
Reconnect or repair as necessary.
Measure the voltage between P/J8990
approximately +5VDC.
Y N
Install a new finisher PWB, PL 13.45 Item
Measure the voltage between P/J8990
the folder home sensor. The voltage changes.
Y N
Install a new folder home sensor,
Install a new finisher PWB, PL 13.45 Item
If the fault persists, install a new finisher PWB,
Launch Issue
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
WARNING
for improper installation.
for a foreign substance.
and P/J8990 on the finisher PWB and between
on the finisher PWB for an open or short circuit, or
PL 13.40 Item 15. If the fault persists, install a
pin 2 and P/J8990 pin 2 on the finisher PWB for an
pins 3 and 1 on the finisher PWB. The voltage is
2.
pin 2 on the finisher PWB and ground. Actuate
PL 13.40 Item 16.
2.
PL 13.45 Item 2.
012-249 Booklet Front Stapler Fail RAP
BSD-ON: BSD 13.4 Office Finisher LX Booklet Interlock Switching
BSD-ON: BSD 13.17 Office Finisher LX Booklet Staple Control (1 of 2 - Front)
012-249 The booklet front staple home switch is not on (does not return to home position)
within the specified time after the booklet front staple motor starts to reverse.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
Check the booklet front stapler for jammed staples or an incorrectly installed staple cartridge.
Procedure
The fold Enter dC330 code 12-024 then 12-025 to cycle the front booklet stapler. The front booklet
stapler cycles normally.
Y N
P/ Measure the voltage between
age is approximately +24VDC.
Y N
Check the circuit from the booklet PWB to the booklet stapler cover switch. Repair
the wiring or install new components as necessary,
Switch off the machine,
and J8894 on the front booklet stapler for a loose or damaged connector, or an open or
short circuit. If the wiring is good, install a new front booklet stapler assembly,
Item 13. If the problem persists, install a new booklet PWB,
Switch off the machine,
and P/J8994 pin 3 on the front booklet stapler for a loose or damaged connector, or an open
or short circuit. If the wiring is good, install a new front booklet stapler assembly,
13. If the problem persists, install a new booklet PWB,
April 2017
2-89
WARNING
GP 10. Disconnect the power cord. Electricity can cause
P/J8993 pin 5 on the booklet PWB and ground. The volt-
PL
GP 10. Check the wiring between
GP 10. Check the wiring between P/J8995
PL 13.70 Item
012-243, 012-265, 012-249
13.70.
P/J8995 on the booklet PWB
PL 13.60
PL 13.70 Item 4.
pin 5 on the booklet PWB
PL 13.60 Item
4.
Status Indicator RAPs