Eject Home Sensor Fail Rap - Xerox VersaLink B7025 Service Manual

A
Y N
Install a new rear tamper home sensor,
Check the wires and connectors for an intermittent open or short circuit. If the fault per-
sists, install a new finisher PWB, PL 12.14 Item
Enter dC330 code 012-026 and 012-029 alternately. The rear tamper motor runs.
Y N
Check the connections of P/J8710 and J8737. The connectors are good.
Y N
Secure the connections.
Check for an open wire or short circuit between
good.
Y N
Repair the open or short circuit.
Measure the voltage between the finisher PWB
between P/J8710 pin 3 (+) and ground (-). The voltage is approximately +24VDC.
Y N
Check the +24VDC circuit. Refer to the
a new finisher PWB, PL 12.14 Item
Install a new rear tamper motor, PL 12.26 Item
isher PWB, PL 12.14 Item 1.
Check the wires and connectors for an intermittent open or short circuit. If the fault persists,
install a new finisher PWB, PL 12.14 Item
Launch Issue
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
PL 12.25 Item 9.
1.
P/J8710 and J8737. The wiring
P/J8710 pin 1 (+) and ground (-), and
Wiring Diagrams. If the fault persists, install
1.
15. If the fault persists, install a new fin-
1.

012-259, 012-280 Eject Home Sensor Fail RAP

BSD-ON: BSD 12.6 Integrated Office Finisher Set Eject (1 of 2)
012-259 The eject home sensor failed to actuate within the specified time.
012-280 The eject home sensor failed to deactuate within the specified time.
Initial Actions
is
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP
death or injury. Moving parts can cause injury.
• Check the eject home sensor,
no foreign object.
• Switch off, then switch on the machine,
Procedure
Check the eject mechanism, PL 12.25
The mechanism is good.
Y N
Repair the mechanism. Install new components as necessary,
Enter dC330 code 012-252. Actuate the eject home sensor. The display changes.
Y N
Check the connections of P/J8700
Y N
Secure the connections.
Check for an open wire or short circuit between
good.
Y N
Repair the open wire or short circuit.
Measure the voltage between the finisher PWB
voltage is approximately +5VDC.
Y N
Check the +5VDC circuit. Refer to the
Measure the voltage between the finisher PWB
the eject home sensor. The voltage changes
Y N
Install a new eject home sensor,
Check the wires and connectors for an intermittent open or short circuit. If the fault per-
sists, install a new finisher PWB,
Enter dC330 code 012-054 and 012-056 alternately. The eject motor runs.
April 2017
2-69
WARNING
10. Disconnect the power cord. Electricity can cause
PL 12.26 Item 9 is correctly installed, not broken and has
GP 10.
for a deformed or broken part and not-seated belts.
PL 12.25.
and P/J8725. The connectors are good.
P/J8700 and P/J8725. The wiring is
P/J8700 pin 9 (+) and ground (-). The
Wiring Diagrams.
P/J8700 pin 2 (+) and ground (-). Actuate
PL 12.26 Item 9.
PL 12.14 Item 1.
Status Indicator RAPs
012-224A, 012-263A, 012-259, 012-280