005-122 DADF Simplex/Side 1 Pre Regi Sensor On Jam
BSD-ON:CH5.4
•
After Pre-Feed started for the first sheet (DADF Feed Motor On (CW)) in Simplex and
Duplex, the DADF Pre Regi Sensor did not turn ON within the specified time.
•
After Pre-Feed started for the second sheet onwards (DADF Feed Motor On (CW)) in
Duplex, the DADF Pre Regi Sensor did not turn ON within the specified time.
Cause/Action
Check the following:
•
Transportation failure due to foreign substance on the document path.
•
The surface of the Feed Roll and Nudger Roll for foreign substances.
•
The surface of the Feed Roll and Nudger Roll for wear.
•
The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure.
•
The DADF Feed Clutch (Output Check [005-062]) for operation failure.
•
The DADF Feed Motor (Output Check [005-008]) for operation failure.
•
The Drive Gear for wear and damage.
If no problem is found, replace the DADF PWB.
005-123 DADF Simplex/Side 1 Regi Sensor On Jam
BSD-ON:CH5.5,
CH5.4
The DADF Regi Sensor does not turn ON within the specified time after the DADF Pre Regi
Sensor On.
Cause/Action
Check the following:
•
Transportation failure due to foreign substance on the document path.
•
The surface of the Takeaway Roll and Regi Roll for foreign substances.
•
The surface of the Takeaway Roll and Regi Roll for wear.
•
The DADF Regi Sensor (Input Check [005-110]) for operation failure.
•
The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure.
•
The DADF T/A Clutch (Output Check [005-098]) for operation failure.
•
The DADF Feed Motor (Output Check [005-008]) for operation failure.
•
The Drive Gear for wear and damage.
If no problem is found, replace the DADF PWB.
Initial Issue
WorkCentre 5021/5019
(PL
56.14)
(PL
56.7)
(PL
56.6)
(PL
56.2)
(PL
56.14)
(PL
56.14)
(PL
56.7)
(PL
56.6)
(PL
56.2)
005-125/145 DADF Regi Sensor Off Jam/ DADF Regi
Sensor Off Jam on Inverting
BSD-ON:CH5.5,
CH5.4
[DADF Regi Sensor Off Jam]
After the DADF Pre Regi Sensor turned OFF at Scan operation, the DADF Regi Sensor did not
turn OFF within the specified time.
[DADF Regi Sensor Off Jam on Inverting]
After the DADF Pre Regi Sensor turned OFF at Invert operation, the DADF Regi Sensor did
not turn OFF within the specified time.
Cause/Action
Check the following:
•
Transportation failure due to foreign substance on the document path.
•
The surface of the Regi Roll, Out Roll, and Exit Roll for foreign substances.
•
The surface of the Regi Roll, Out Roll, and Exit Roll for wear.
•
The DADF Regi Sensor (Input Check [005-110]) for operation failure.
•
The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure.
•
The DADF Feed Motor (Output Check [005-008]) for operation failure.
•
The Drive Gear for wear and damage.
If no problem is found, replace the DADF PWB.
005-131/132 DADF Invert Sensor On Jam on Inverting/
DADF Invert Sensor On Jam
BSD-ON:CH5.5,
CH5.4
[DADF Invert Sensor On Jam on Inverting]
After the DADF Regi Sensor turned ON at Invert operation, the DADF Invert Sensor did not
turn ON within the specified time.
[DADF Invert Sensor On Jam]
After the DADF Regi Sensor turned ON in the Scan operation, the DADF Invert Sensor did not
turn ON within the specified time.
Cause/Action
Check the following:
•
Transportation failure due to foreign substance on the document path.
08/2012
2-13
(PL
56.14)
(PL
56.14)
(PL
56.6)
(PL
56.2)
Status Indicator RAPs
005-122, 005-125/145