Mitsubishi Electric GT14 User Manual page 456

PLC
Ethernet module
Model
*3*4
AJ71E71N3-T
AJ71E71N-B5
AJ71E71N-B2
MELSEC-A AJ71E71N-T
AJ71E71N-B5T
MELSEC-Q
AJ71E71-S3
(A mode) A1SJ71E71N3-T
A1SJ71E71N-B5
Motion controller
A1SJ71E71N-B2
CPU (A Series)
A1SJ71E71N-T
A1SJ71E71N-B5T
A1SJ71E71-B5-S3
A1SJ71E71-B2-S3
MELSEC-L LJ71E71-100
*1 The destination connected with the twisted pair cable varies with the configuration of the applicable Ethernet network system.
Connect to the Ethernet module, hub, transceiver, wireless LAN adapter (such as NZ2WL-JPA and NZ2WL-JPS), or other system
equipment corresponding to the applicable Ethernet network system.
Use cables, connectors, and hubs that meet the IEEE802.3 10BASE-T/100BASE-TX standard.
A cross cable is available for connecting the GOT to the Ethernet module.
The use of shielded twisted pair cable (STP) is recommended in environments in which the performance against noise is
required.
For the controllers that allow the connection of a wireless LAN adapter and the setting method of wireless LAN adapters, refer to
the manual of the wireless LAN adapter to be used.
*2 A length between a hub and a node.
The maximum distance differs depending on the Ethernet device to be used.
The following shows the number of the connectable nodes when a repeater hub is used.
• 10BASE-T: Max. 4 nodes for a cascade connection (500m)
• 100BASE-TX: Max. 2 nodes for a cascade connection (205m)
When switching hubs are used, the cascade connection between the switching hubs has no logical limit for the number of
cascades.
For the limit, contact the switching hub manufacturer.
*3 For the system configuration of the Ethernet module, refer to the following manuals.
*4 Select one of the following [Type] in [Ethernet setting] of GT Designer3.
• Ethernet module (MELSEC iQ-R Series): RJ71EN71
• Ethernet module (Q Series): QJ71E71
• Ethernet module (QnA Series): AJ71QE71
• Ethernet module (A Series): AJ71E71
For [Ethernet] of GT Designer3, refer to the following.
*5 When using the PERIPHERAL I/F of Q170MCPU or Q17nDCPU-S1, refer to the following.
*6 The number of connectable GOTs for one network is 63 units (at most).
*7 Use C or later version of GT11H-C-37P.
*8 Connect the GOT to the Ethernet module controlled by the RCPU of another CPU on the multiple CPU.
23 - 6
23. ETHERNET CONNECTION
23.2 System Configuration
Connection cable
Communication
Cable model
type
• 10BASE-T
Shielded twisted pair
cable (STP)
or
Unshielded twisted pair
cable (UTP)
Ethernet
Category 3, 4, and 5
• 100BASE-TX
Shielded twisted pair
cable (STP)
Category 5 and 5e
Q Corresponding Ethernet Interface Module User's Manual (Basic)
For QnA Ethernet Interface Module User's Manual
For A Ethernet Interface Module User's Manual
23.3.3 Ethernet setting
23.2.5 Connecting to PERIPHERAL I/F
*1
Connector
External cable
conversion box
GT14H-C30-42P(3m)
GT16H-CNB-42S GT14H-C60-42P(6m)
GT14H-C100-42P(10m)
GT11H-C30-37P (3m)
GT16H-CNB-37S GT11H-C60-37P (6m)
GT11H-C100-37P(10m)
GT14H-C30-42P(3m)
GT16H-CNB-42S GT14H-C60-42P(6m)
GT14H-C100-42P(10m)
GT11H-C30-37P (3m)
GT16H-CNB-37S GT11H-C60-37P (6m)
GT11H-C100-37P(10m)
Maximum Number of
GOT
*7
segment connectable
model
length equipment
128 GOTs
(recommend
*2
100m
ed to 16
units or less)
*6