Gestetner G060 Service Manual page 561

Mode No.
2
(Class 1, 2, and 3)
301 46 [FC,Y]SP S 62.5
47 [FC,M]SP S 62.5
48 [FC,C]SP S 62.5
49 [FC,K]SP S 125
50 [FC,Y]SP S 125
51 [FC,M]SP S 125
52 [FC,C]SP S 125
57 [K]TH S 62.5
58 [FC,K]TH S 62.5
59 [FC,Y]TH S 62.5
60 [FC,M]TH S 62.5
61 [FC,C]TH S 62.5
62 [K]SP D 62.5
63 [K]SP D 125
64 [K]SP D 185
65 [FC,K]SP D 62.5
66 [FC,Y]SP D 62.5
67 [FC,M]SP D 62.5
68 [FC,C]SP D 62.5
69 [FC,K]SP D 125
70 [FC,Y]SP D 125
71 [FC,M]SP D 125
72 [FC,C]SP D 125
[Current Paper Size] Transfer Current - Paper Size Correction
309
Paper Type -> N: Normal, TH: Thick, OHP
Corrects the transfer current for paper size.
When small paper is used for printing, the transfer current flows to the drum at the non
image areas where the transfer belt touches the OPC drum. This may cause an abnormal
image due to insufficient current at the image areas.
To increase the current by 1.5 times, set the SP mode to "15".
NOTE: Increase only when an abnormal image (insufficient image transfer) occurs on a
small paper size. However, increasing the current too much may cause image
offset.
5 N LT SEF
6 N A5 SEF
7 TH LT SEF
8 TH A5 SEF
9 OHP LT SEF
10 OHP A5 SEF
SM
Function / [ Setting ]
[ 0 to 50 / 7 / 1 µA/step ]
*
[ 0 to 50 / 6 / 1 µA/step ]
BCU
[ 0 to 50 / 7 / 1 µA/step ]
[ 0 to 50 / 15 / 1 µA/step ]
[ 0 to 50 / 14 / 1 µA/step ]
[ 0 to 50 / 12 / 1 µA/step ]
[ 0 to 50 / 13 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 9 / 1 µA/step ]
[ 0 to 50 / 18 / 1 µA/step ]
[ 0 to 50 / 27 / 1 µA/step ]
[ 0 to 50 / 10 / 1 µA/step ]
[ 0 to 50 / 7 / 1 µA/step ]
[ 0 to 50 / 6 / 1 µA/step ]
[ 0 to 50 / 7 / 1 µA/step ]
[ 0 to 50 / 18 / 1 µA/step ]
[ 0 to 50 / 13 / 1 µA/step ]
[ 0 to 50 / 11 / 1 µA/step ]
[ 0 to 50 / 12 / 1 µA/step ]
* [ 10 to 40 / 16 / 0.1/step ]
BCU
[ 10 to 40 / 22 / 0.1/step ]
[ 10 to 40 / 12 / 0.1/step ]
[ 10 to 40 / 30 / 0.1/step ]
[ 10 to 40 / 22 / 0.1/step ]
[ 10 to 40 / 40 / 0.1/step ]
5-23
COPY SP MODE
G570