Motor Data Sets (Mds) - Siemens SINAMICS G120 List Manual

Parameters
Symbol Meaning
Parameter name [Unit] Monitoring parameter with
rxxxx[y..z] unit [Unit] and index range
[y..z] or data set [C/D]
Parameter name Setting parameter
from ... to [Unit] with min/max value
pxxxx[C/D] (Def) and unit [Unit] data
set [C/D] and factory
setting (Def) *)
Data sets
Symbol Meaning
pxxxx[C] Parameter belongs to the
Command Data Set (CDS).
pxxxx[D] Parameter belongs to the
Drive Data Set (DDS).
pxxxx[E] Parameter belongs to the
Encoder Data Set (EDS).
pxxxx[M] Parameter belongs to the
Motor Data Set (MDS).
pxxxx[P] Parameter belongs to the
Power unit Data Set (PDS).
*)
For some parameters the value for the factory setting is calculated during commissioning for they are dependent on Power Module and motor (see Section 2.1.1 "Calculated").
1 2
Explanations on the function diagrams
Explanation of the symbols (part 1)
Connectors
Symbol Meaning
Connector input CI
Parameter name
with index range [y..z]
pxxxx[y..z]
(Def)
or data set [C/D]
and factory setting
(Def) *)
Parameter name [Unit]
rxxxx[y..z]
Connector output CO with
unit [Unit] and with index
range [y..z]
CI: Connector Input
CO: Connector Output
CO/BO: Connector/Binector Output
Information on parameters, binectors, connectors
Symbol Meaning
Parameter name Parameter name (up to 18 characters)
[Unit] [dimension unit]
rxxxx[y] or "r" = monitoring parameter. These parameters are read-only
rxxxx[y...z] or "xxxx" stands for the parameter number
rxxxx[y].ww or "[y]" specifies the applicable index, "[y...z]" specifies the index range
rxxxx.ww ".ww" specifies the bit number (e.g. 0...15).
pxxxx[y] or "p" = setting parameter. These parameters can be changed.
pxxxx[y...z] or "xxxx" stands for the parameter number,
pxxxx[y].ww or "[y]" specifies the applicable index, "[y...z]" specifies the index range ".ww"
pxxxx.ww specifies the bit number (e.g. 0...15).
from ... to Value range.
(xxxx[y].ww) Parameter number (xxxx) with Index number [y] and bit number .ww.
(Def) Factory setting.
(Def.w) Factory setting with bit number as prefix.
[aaaa.b] Diagram references for setting parameters that occur a multiple number of times.
[Function diagram number, signal path]
3 4
Binectors
Symbol Meaning
Binector input BI with
Parameter name
with index range [y..z] or
pxxxx[y..z]
data set [C/D] and
(Def.y)
factory setting.bit
number (Def)
Parameter name
rxxxx Binector output BO
Parameter name
BI: Binector Input
BO: Binector Output
5 6
fp_1020_97_61.vsd
09.12.2015
Connectors/binectors
Symbol Meaning
Parameter name
rxxxx Connector/binector output
rxxxx CO/BO
Pre-assigned connectors and binectors
Symbol Meaning
Setting parameter with
min/max value and unit
from ... to [Unit]
[Unit] data set [D] and
pxxxx[D] (Def)
factory setting (Def)
Cross references between diagrams
Symbol Meaning
Signal The function diagrams are sub-divided into
path signal paths 1...8 in order to facilitate
orientation.
Text Text = Unique signal designation
[aaaa.b]
aaaa = Signal to target diagram aaa
b = Signal to signal path b
Text Text = Unique signal designation
[cccc.d]
cccc = Signal from source diagram cccc
d = Signal from signal path d
To "function diagram name" [aaaa.b] = binectors.
Cross references for control bits
Symbol Meaning
pxxxx= Original parameter of signal
pxxxx
aaaa = Signal from source diagram aaaa
[aaaa.b]
b = Signal from signal path b
7
Function diagram
G120 CU240B/E-2
V4.7.6
8
- 1020 -