Siemens SINAMICS G120 List Manual page 919

RSR 0 ... 2, 729
Sampling times of the runtime groups, 715
SUB 0 ... 1, 720
XOR 0 ... 3, 718
Function diagrams, general information
Explanation of the symbols (part 1), 563
Explanation of the symbols (part 2), 564
Explanation of the symbols (part 3), 565
Handling BICO technology, 566
Function diagrams, input/outputterminals
Connection overview CU240B-2, 568
Connection overview CU240E-2, 569
CU240B-2 analog input 0 (AI 0), 574
CU240B-2 analog inputs as digital inputs (DI 11), 576
CU240B-2 analog output (AO 0), 578
CU240B-2 digital inputs, electrically isolated
(DI 0 ... DI 3), 570
CU240B-2 digital output (DO 0), 572
CU240E-2 analog inputs as digital inputs
(DI 11 ... DI 12), 577
CU240E-2 analog inputs 0 ... 1 (AI 0 ... AI 1), 575
CU240E-2 analog outputs 0 ... 1 (AO 0 ... AO 1), 579
CU240E-2 digital inputs, electrically isolated
(DI 0 ... DI 5), 571
CU240E-2 digital outputs (DO 0 ... DO 2), 573
Three-wire control, 581
Two-wire control, 580
Function diagrams, internal control/status words
Control word faults/alarms (r2138), 623
Control word sequence control (r0898), 609
Control word setpoint channel (r1198), 611
Control word 1 (r0054), 614
Control word, speed controller (r1406), 616
Sequence control - missing enable signals, line
contactor control, 626
Sequence control - Sequencer, 625
Status word faults/alarms 1 and 2 (r2139 and r2135),
624
Status word monitoring functions 1 (r2197), 620
Status word monitoring functions 2 (r2198), 621
Status word monitoring functions 3 (r2199), 622
Status word sequence control (r0899), 610
Status word 1 (r0052), 612
Status word 2 (r0053), 613
Status word, closed-loop control (r0056), 618
Status word, current control (r1408), 619
Status word, speed controller (r1407), 617
Supplementary control word (r0055), 615
Function diagrams, PROFIenergy
Control commands and interrogation commands,
583
States, 584
SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
Function diagrams, Safety Integrated Basic Functions
F-DI (Fail-safe Digital Input), 635
Monitoring functions and faults/alarms, 631
Parameter manager, 630
Status words, 632
STO (Safe Torque Off) (Part 1), 633
STO (Safe Torque Off) (Part 2) - PM240-2 FS D-F,
634
Function diagrams, Safety Integrated Extended
Functions
Control and status word, 642
Extended Functions via F-DI (p9601.2 = 1 and
p9601.3 = 0), 644
Extended Functions via PROFIsafe (9601.2 = 1 and
9601.3 = 1), 645
Fail-safe digital inputs (F-DI 0 ... F-DI 2), 643
Parameter manager, 637
SDI (Safe Direction), 641
SLS (Safely-Limited Speed), 639
SS1 (Safe Stop 1), internal STOP A, B, F, 638
SSM (Safe Speed Monitor), 640
Function diagrams, Safety Integrated PROFIsafe
Manufacturer-specific telegrams, 648
Standard telegrams, 647
Function diagrams, setpoint channel
Direction limitation and direction reversal, 655
Fixed speed setpoints, binary selection (p1016 = 2),
651
Fixed speed setpoints, direct selection (p1016 = 1),
652
Main/supplementary setpoint, setpointscaling,
jogging, 654
Motorized potentiometer, 653
Overview, 650
Ramp-function generator (basic), 657
Ramp-function generator (extended), 658
Ramp-function generator selection, -status word,
-tracking, 659
Skip frequency bands and speedlimitations, 656
Function diagrams, signals and monitoring functions
Overview, 741
Function diagrams, signals and monitoringfunctions
Load monitoring (Part 1), 745, 746
Monitoring functions 1, 752
Monitoring functions 2, 753
Motor temperature model 1 (I2t), 748
Motor temperature model 2, 749
Motor temperature model 3, 750
Speed messages 1, 742
Speed messages 2, 743
Thermal monitoring, motor, motor temperature status
word, faults/alarms, 747
Thermal monitoring, power unit, 751
Torque signals, motor blocked/stalled, 744
Index
919