Siemens SINAMICS G120 List Manual page 548

2 Parameters
2.4 BICO parameters (connectors/binectors)
p2203[0...n]
p2204[0...n]
p2205[0...n]
p2206[0...n]
p2207[0...n]
p2208[0...n]
p2209[0...n]
p2210[0...n]
p2211[0...n]
p2212[0...n]
p2213[0...n]
p2214[0...n]
p2215[0...n]
r2224
r2245
r2250
r2260
r2262
r2266
r2272
r2273
p2291
p2292
r2294
p2295
r2344
p2900[0...n]
p2901[0...n]
r2902[0...14]
p2930[0...n]
r3131
r3132
r3841
r8541
r9712
r9713[0...5]
r9714[0...2]
r9733[0...2]
r20095
r20099
r20103
r20107
r20111
r20115
r20119[0...2]
r20124[0...2]
r20129
r20134
r20220
r20225
r20231
r20239
r20247
r20253
r20261
548
CO: Technology controller fixed value 3 / Tec_ctr fix val 3
CO: Technology controller fixed value 4 / Tec_ctr fix val 4
CO: Technology controller fixed value 5 / Tec_ctr fix val 5
CO: Technology controller fixed value 6 / Tec_ctr fix val 6
CO: Technology controller fixed value 7 / Tec_ctr fix val 7
CO: Technology controller fixed value 8 / Tec_ctr fix val 8
CO: Technology controller fixed value 9 / Tec_ctr fix val 9
CO: Technology controller fixed value 10 / Tec_ctr fix val 10
CO: Technology controller fixed value 11 / Tec_ctr fix val 11
CO: Technology controller fixed value 12 / Tec_ctr fix val 12
CO: Technology controller fixed value 13 / Tec_ctr fix val 13
CO: Technology controller fixed value 14 / Tec_ctr fix val 14
CO: Technology controller fixed value 15 / Tec_ctr fix val 15
CO: Technology controller fixed value effective / Tec_ctr FixVal eff
CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
CO: Technology controller actual value after filter / Tec_ctr act aftFlt
CO: Technology controller actual value scaled / Tech_ctrl act scal
CO: Technology controller system deviation / Tec_ctrl sys_dev
CO: Technology controller maximum limiting / Tec_ctrl max_lim
CO: Technology controller minimum limiting / Tec_ctrl min_lim
CO: Technology controller output signal / Tec_ctrl outp_sig
CO: Technology controller output scaling / Tec_ctrl outp scal
CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
CO: Fixed value 1 [%] / Fixed value 1 [%]
CO: Fixed value 2 [%] / Fixed value 2 [%]
CO: Fixed values [%] / Fixed values [%]
CO: Fixed value M [Nm] / Fixed value M [Nm]
CO: Actual fault value / Act fault val
CO: Actual component number / Comp_no act
CO: Friction characteristic output / Frict outp
CO: Speed setpoint from BOP/IOP in the manual mode / N_set OP
CO: SI Motion diagnostics pos. act. val. motor side (processor 1) / SI Mtn s_act motP1
CO: SI Motion diagnostics position actual value load side / SI Mtn s_act load
CO: SI Motion diagnostics velocity (processor 1) / SI Mtn diag v P1
CO: SI Motion setpoint speed limit effective / SI Mtn setp_lim
CO: ADD 0 output Y / ADD 0 output Y
CO: ADD 1 output Y / ADD 1 output Y
CO: SUB 0 difference Y / SUB 0 difference Y
CO: SUB 1 difference Y / SUB 1 difference Y
CO: MUL 0 product Y / MUL 0 product Y
CO: MUL 1 product Y / MUL 1 product Y
CO: DIV 0 quotient / DIV 0 quotient
CO: DIV 1 quotient / DIV 1 quotient
CO: AVA 0 output Y / AVA 0 output Y
CO: AVA 1 output Y / AVA 1 output Y
CO: NSW 0 output Y / NSW 0 output Y
CO: NSW 1 output Y / NSW 1 output Y
CO: LIM 0 output Y / LIM 0 output Y
CO: LIM 1 output Y / LIM 1 output Y
CO: PT1 0 output Y / PT1 0 output Y
CO: PT1 1 output Y / PT1 1 output Y
CO: INT 0 output Y / INT 0 output Y
SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529