Siemens SINAMICS G120 List Manual page 531

p2296[0...n]
p2297[0...n]
p2298[0...n]
p2299[0...n]
p3111[0...n]
p3112[0...n]
p3230[0...n]
p3232[0...n]
p3330[0...n]
p3331[0...n]
p3332[0...n]
2.3.2 Drive Data Sets (DDS)
Product: SINAMICS G120 CU240, Version: 4707900, Language: eng, Type: DDS
p0340[0...n]
p0640[0...n]
p1001[0...n]
p1002[0...n]
p1003[0...n]
p1004[0...n]
p1005[0...n]
p1006[0...n]
p1007[0...n]
p1008[0...n]
p1009[0...n]
p1010[0...n]
p1011[0...n]
p1012[0...n]
p1013[0...n]
p1014[0...n]
p1015[0...n]
p1030[0...n]
p1037[0...n]
p1038[0...n]
p1040[0...n]
p1047[0...n]
p1048[0...n]
p1058[0...n]
p1059[0...n]
p1063[0...n]
p1080[0...n]
p1082[0...n]
p1083[0...n]
p1086[0...n]
p1091[0...n]
p1092[0...n]
p1093[0...n]
p1094[0...n]
p1101[0...n]
p1120[0...n]
p1121[0...n]
p1123[0...n]
p1127[0...n]
SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
CI: Technology controller output scaling / Tec_ctrl outp scal
CI: Technology controller maximum limit signal source / Tec_ctrMaxLimS_src
CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
CI: Technology controller limit offset / Tech_ctrl lim offs
BI: External fault 3 enable / Ext fault 3 enab
BI: External fault 3 enable negated / Ext flt 3 enab neg
CI: Load monitoring speed actual value / Load monit n_act
BI: Load monitoring failure detection / Load_moni fail_det
BI: 2/3 wire control command 1 / 2/3 wire cmd 1
BI: 2/3 wire control command 2 / 2/3 wire cmd 2
BI: 2/3 wire control command 3 / 2/3 wire cmd 3
Automatic calculation motor/control parameters / Calc auto par
Current limit / Current limit
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
CO: Fixed speed setpoint 4 / n_set_fixed 4
CO: Fixed speed setpoint 5 / n_set_fixed 5
CO: Fixed speed setpoint 6 / n_set_fixed 6
CO: Fixed speed setpoint 7 / n_set_fixed 7
CO: Fixed speed setpoint 8 / n_set_fixed 8
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
CO: Fixed speed setpoint 11 / n_set_fixed 11
CO: Fixed speed setpoint 12 / n_set_fixed 12
CO: Fixed speed setpoint 13 / n_set_fixed 13
CO: Fixed speed setpoint 14 / n_set_fixed 14
CO: Fixed speed setpoint 15 / n_set_fixed 15
Motorized potentiometer configuration / Mop configuration
Motorized potentiometer maximum speed / MotP n_max
Motorized potentiometer minimum speed / MotP n_min
Motorized potentiometer starting value / Mop start value
Motorized potentiometer ramp-up time / Mop ramp-up time
Motorized potentiometer ramp-down time / Mop ramp-down time
Jog 1 speed setpoint / Jog 1 n_set
Jog 2 speed setpoint / Jog 2 n_set
Setpoint channel speed limit / Setp_chan n_lim
Minimum speed / n_min
Maximum speed / n_max
CO: Speed limit in positive direction of rotation / n_limit pos
CO: Speed limit in negative direction of rotation / n_limit neg
Skip speed 1 / n_skip 1
Skip speed 2 / n_skip 2
Skip speed 3 / n_skip 3
Skip speed 4 / n_skip 4
Skip speed bandwidth / n_skip bandwidth
Ramp-function generator ramp-up time / RFG ramp-up time
Ramp-function generator ramp-down time / RFG ramp-down time
Ramp-function generator minimum ramp-up time / RFG t_RU min
Ramp-function generator minimum ramp-down time / RFG t_RD min
2 Parameters
2.3 Parameters for data sets
531