Siemens SINAMICS G120 List Manual page 142
Hide thumbs
Also See for SINAMICS G120:
- List manual (1256 pages) ,
- Manual (732 pages) ,
- Operating instructions manual (550 pages)
Table of Contents
Advertisement
2 Parameters
2.2 List of parameters
r0981[0...299]
List of existing parameters 2 / List avail par 2
Access level: 4
Can be changed: -
Unit group: -
Min
-
Description:
Displays the parameters that exist for this drive.
Dependency:
Refer to: r0980, r0989
Note:
Modified parameters are displayed in indices 0 to 298. If an index contains the value 0, then the list ends here. In a
long list, index 299 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0980[0...299], r0981[0...299] ... r0989[0...299]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0989[0...299]
List of existing parameters 10 / List avail par 10
Access level: 4
Can be changed: -
Unit group: -
Min
-
Description:
Displays the parameters that exist for this drive.
Dependency:
Refer to: r0980, r0981
Note:
Modified parameters are displayed in indices 0 to 298. If an index contains the value 0, then the list ends here.
This list consists solely of the following parameters:
r0980[0...299], r0981[0...299] ... r0989[0...299]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0990[0...99]
List of modified parameters 1 / List chang par 1
Access level: 4
Can be changed: -
Unit group: -
Min
-
Description:
Displays those parameters with a value other than the factory setting for this drive.
Dependency:
Refer to: r0991, r0999
Note:
Modified parameters are displayed in indices 0 to 98. If an index contains the value 0, then the list ends here. In a
long list, index 99 contains the parameter number at which position the list continues.
This list consists solely of the following parameters:
r0990[0...99], r0991[0...99] ... r0999[0...99]
The parameters in this list are not displayed in the expert list of the commissioning software. However, they can be
read from a higher-level control system (e.g. PROFIBUS master).
r0991[0...99]
List of modified parameters 2 / List chang par 2
Access level: 4
Can be changed: -
Unit group: -
Min
-
Description:
Displays those parameters with a value other than the factory setting for this drive.
Dependency:
Refer to: r0990, r0999
142
Calculated: -
Scaling: -
Unit selection: -
Max
-
Calculated: -
Scaling: -
Unit selection: -
Max
-
Calculated: -
Scaling: -
Unit selection: -
Max
-
Calculated: -
Scaling: -
Unit selection: -
Max
-
SINAMICS G120 Control Units CU240B-2/CU240E-2
Data type: Unsigned16
Dyn. index: -
Func. diagram: -
Factory setting
-
Data type: Unsigned16
Dyn. index: -
Func. diagram: -
Factory setting
-
Data type: Unsigned16
Dyn. index: -
Func. diagram: -
Factory setting
-
Data type: Unsigned16
Dyn. index: -
Func. diagram: -
Factory setting
-
List Manual (LH11), 01/2016, A5E33839529
Hide quick links:
Advertisement
Chapters
Table of Contents
