Siemens SINAMICS G120 List Manual page 547

r1119
r1149
r1150
r1169
r1170
r1258
r1298
r1337
r1343
r1348
p1351[0...n]
r1438
r1445
r1454
r1468
r1482
r1490
r1493
r1508
r1516
r1518[0...1]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
r1526
r1527
r1538
r1539
r1547[0...1]
r1548[0...1]
p1563[0...n]
p1564[0...n]
p1570[0...n]
r1593[0...1]
r1597
r1598
r1718
r1723
r1732[0...1]
r1733[0...1]
r1770
r1771
r1801[0...1]
r1809
r2050[0...11]
r2060[0...10]
r2089[0...4]
r2120
r2121
r2131
r2132
r2169
p2201[0...n]
p2202[0...n]
SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
CO: Ramp-function generator setpoint at the input / RFG setp at inp
CO: Ramp-function generator acceleration / RFG acceleration
CO: Ramp-function generator speed setpoint at the output / RFG n_set at outp
CO: Speed controller speed setpoints 1 and 2 / n_ctrl n_set 1/2
CO: Speed controller setpoint sum / n_ctrl setp sum
CO: Vdc controller output / Vdc_ctrl output
CO: Vdc controller output (U/f) / Vdc_ctrl output
CO: Actual slip compensation / Slip comp act val
CO: I_max controller frequency output / I_max_ctrl f_outp
CO: U/f control Eco factor actual value / U/f Eco fac act v
CO: Motor holding brake starting frequency / Brake f_start
CO: Speed controller speed setpoint / n_ctrl n_set
CO: Actual speed smoothed / n_act smooth
CO: Speed controller system deviation I component / n_ctrl sys dev Tn
CO: Speed controller P-gain effective / n_ctr Kp eff
CO: Speed controller I torque output / n_ctrl I-M_outp
CO: Droop feedback speed reduction / Droop n_reduction
CO: Moment of inertia total, scaled / M_inert tot scal
CO: Torque setpoint before supplementary torque / M_set bef. M_suppl
CO: Supplementary torque and acceleration torque / M_suppl + M_accel
CO: Accelerating torque / M_accel
CO: Torque limit upper / M_max upper
CO: Torque limit lower / M_max lower
CO: Torque limit upper scaling / M_max upper scal
CO: Torque limit lower scaling / M_max lower scal
CO: Torque limit upper without offset / M_max up w/o offs
CO: Torque limit lower without offset / M_max low w/o offs
CO: Upper effective torque limit / M_max upper eff
CO: Lower effective torque limit / M_max lower eff
CO: Torque limit for speed controller output / M_max outp n_ctrl
CO: Stall current limit torque-generating maximum / Isq_max stall
CO: Mom. of inertia estimator load torque direction of rotation pos. / J_est M pos
CO: Mom. of inertia estimator load torque direction of rotation neg. / J_est M neg
CO: Flux setpoint / Flex setp
CO: Field weakening controller / flux controller output / Field/Fl_ctrl outp
CO: Field weakening controller output / Field_ctrl outp
CO: Total flux setpoint / Flux setp total
CO: Isq controller output / Isq_ctrl outp
CO: Isd controller output / Isd_ctrl outp
CO: Direct-axis voltage setpoint / Direct U set
CO: Quadrature-axis voltage setpoint / Quad U set
CO: Motor model speed adaptation proportional component / MotMod n_adapt Kp
CO: Motor model speed adaptation I comp. / MotMod n_adapt Tn
CO: Pulse frequency / Pulse frequency
CO: Modulator mode actual / Modulator mode act
CO: PROFIBUS PZD receive word / PZD recv word
CO: PROFIdrive PZD receive double word / PZD recv DW
CO: Send binector-connector converter status word / Bin/con ZSW send
CO: Sum of fault and alarm buffer changes / Sum buffer changed
CO: Counter alarm buffer changes / Alrm buff changed
CO: Actual fault code / Act fault code
CO: Actual alarm code / Actual alarm code
CO: Actual speed smoothed signals / n_act smth message
CO: Technology controller fixed value 1 / Tec_ctrl fix val1
CO: Technology controller fixed value 2 / Tec_ctr fix val 2
2.4 BICO parameters (connectors/binectors)
2 Parameters
547