Siemens SINAMICS G120 List Manual page 252

2 Parameters
2.2 List of parameters
Dependency: Not visible with application class: "Standard Drive Control" (SDC, p0096 = 1), "Dynamic Drive Control" (DDC, p0096
= 2)
p1780[0...n] Motor model adaptation configuration / MotMod adapt conf
Access level: 3
Can be changed: U, T
Unit group: -
Min
-
Description: Sets the configuration for the adaptation circuit of the motor model.
Induction motor (ASM): Rs, Lh, and offset compensation.
Permanent-magnet synchronous motor (PMSM): kT
Bit field: Bit
01
02
03
04
06
07
10
12
13
14
15
Dependency: In U/f characteristic operating mode only bit 7 is relevant.
For active motor model feedback (see p1784), the Lh adaptation is internally de-activated automatically.
Note: ASM: Induction motor
PMSM: permanent-magnet synchronous motor
When selecting the compensation of the valve interlocking via Rs (bit 7), the compensation in the gating unit is de-
activated and is instead taken into account in the motor model.
In order that the correction values of the Rs, Lh and kT adaptation (selected using Bit 0 ... Bit 2) are correctly
accepted when changing over the drive data set, a dedicated motor number must be entered into p0826 for each
different motor.
For bit 12 (only for synchronous motors and bit 6 = 1):
The pole position identification is only carried out after power on and after the motor has coasted down. The switch-
off speed p1226 should be as low as possible. If the power unit is switched off when the motor is stationary, then the
next time that the power unit is switched on, the old angle is used as starting value. The precondition applies that
while the power unit is switched off the motor does not rotate.
The duration of the pole position identification is shortened using bit 13. As a consequence, the pole wheel angle
error can be slightly greater.
p1784[0...n] Motor model feedback scaling / MotMod fdbk scal
Access level: 4
Can be changed: U, T
Unit group: -
Min
0.0 [%]
Description: Sets the scaling for model fault feedback.
Dependency: Not visible with application class: "Standard Drive Control" (SDC, p0096 = 1), "Dynamic Drive Control" (DDC, p0096
= 2)
Note: Feeding back the measured model fault to the model states increases the control stability and makes the motor
model rugged against parameter errors.
When feedback is selected (p1784 > 0), Lh adaptation is not effective.
252
Signal name
Select motor model ASM Rs adaptation
Select motor model ASM Lh adaptation
Select motor model PMSM kT adaptation
Select motor model offset adaptation
Select pole position identification PMSM
encoderless
Select T(valve) with Rs adaptation
Filter time combination current like current
ctrl integral time
Start PMSM sensorless with last angle
Fast pulsed pole position identification
Delay of the precontrol speed to the motor
model
RESM Q flux model linear active
Calculated: p0340 = 1,3,4
Scaling: -
Unit selection: -
Max
-
1 signal
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Calculated: p0340 = 1,3,4
Scaling: -
Unit selection: -
Max
1000.0 [%]
SINAMICS G120 Control Units CU240B-2/CU240E-2
Data type: Unsigned16
Dyn. index: DDS, p0180
Func. diagram: -
Factory setting
0000 0000 0101 1100 bin
0 signal
No
No
No
No
No
No
No
No
No
No
No
Data type: FloatingPoint32
Dyn. index: DDS, p0180
Func. diagram: -
Factory setting
0.0 [%]
List Manual (LH11), 01/2016, A5E33839529
FP
-
-
-
-
-
-
-
-
-
-
-