Siemens SINAMICS G120 List Manual page 533

p1336[0...n]
p1338[0...n]
p1339[0...n]
p1340[0...n]
p1341[0...n]
p1345[0...n]
p1346[0...n]
p1349[0...n]
p1350[0...n]
p1351[0...n]
p1400[0...n]
p1401[0...n]
p1402[0...n]
p1416[0...n]
p1452[0...n]
p1456[0...n]
p1457[0...n]
p1458[0...n]
p1459[0...n]
p1461[0...n]
p1463[0...n]
p1464[0...n]
p1465[0...n]
p1470[0...n]
p1472[0...n]
p1487[0...n]
p1488[0...n]
p1489[0...n]
p1496[0...n]
p1498[0...n]
p1499[0...n]
p1514[0...n]
p1517[0...n]
p1520[0...n]
p1521[0...n]
p1524[0...n]
p1525[0...n]
p1530[0...n]
p1531[0...n]
p1553[0...n]
p1560[0...n]
p1561[0...n]
p1562[0...n]
p1563[0...n]
p1564[0...n]
p1570[0...n]
p1573[0...n]
p1574[0...n]
p1575[0...n]
p1580[0...n]
p1582[0...n]
p1584[0...n]
p1586[0...n]
p1590[0...n]
p1594[0...n]
SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
Slip compensation limit value / Slip comp lim val
U/f mode resonance damping gain / Uf Res_damp gain
U/f mode resonance damping filter time constant / Uf Res_damp T
I_max frequency controller proportional gain / I_max_ctrl Kp
I_max frequency controller integral time / I_max_ctrl Tn
I_max voltage controller proportional gain / I_max_U_ctrl Kp
I_max voltage controller integral time / I_max_U_ctrl Tn
U/f mode resonance damping maximum frequency / Uf res_damp f_max
U/f control soft start / U/f soft start
CO: Motor holding brake starting frequency / Brake f_start
Speed control configuration / n_ctrl config
Flux control configuration / Flux ctrl config
Closed-loop current control and motor model configuration / I_ctrl config
Speed setpoint filter 1 time constant / n_set_filt 1 T
Speed controller speed actual value smoothing time (sensorless) / n_C n_act T_s SL
Speed controller P gain adaptation lower starting point / n_ctrl AdaptKpLow
Speed controller P gain adaptation upper starting point / n_ctrl AdaptKp up
Adaptation factor lower / Adapt_factor lower
Adaptation factor upper / Adapt_factor upper
Speed controller Kp adaptation speed upper scaling / n_ctr Kp n up scal
Speed controller Tn adaptation speed upper scaling / n_ctr Tn n up scal
Speed controller adaptation speed lower / n_ctrl n lower
Speed controller adaptation speed upper / n_ctrl n upper
Speed controller encoderless operation P-gain / n_ctrl SL Kp
Speed controller encoderless operation integral time / n_ctrl SL Tn
Droop compensation torque scaling / Droop M_comp scal
Droop input source / Droop input source
Droop feedback scaling / Droop scal
Acceleration pre-control scaling / a_prectrl scal
Load moment of inertia / Load M_inertia
Accelerating for torque control scaling / a for M_ctrl scal
Supplementary torque 2 scaling / M_suppl 2 scal
Accelerating torque smoothing time constant / M_accel T_smooth
CO: Torque limit upper / M_max upper
CO: Torque limit lower / M_max lower
CO: Torque limit upper scaling / M_max upper scal
CO: Torque limit lower scaling / M_max lower scal
Power limit motoring / P_max mot
Power limit regenerative / P_max gen
Stall limit scaling / Stall limit scal
Moment of inertia estimator accelerating torque threshold value / J_est M thresh
Moment of inertia estimator change time moment of inertia / J_est t J
Moment of inertia estimator change time load / J_est t load
CO: Mom. of inertia estimator load torque direction of rotation pos. / J_est M pos
CO: Mom. of inertia estimator load torque direction of rotation neg. / J_est M neg
CO: Flux setpoint / Flex setp
Flux threshold value magnetizing / Flux thresh magnet
Voltage reserve dynamic / U_reserve dyn
Voltage target value limit / U_tgt val lim
Efficiency optimization / Efficiency opt.
Flux setpoint smoothing time / Flux setp T_smth
Field weakening operation flux setpoint smoothing time / Field weak T_smth
Field weakening characteristic scaling / Field weak scal
Flux controller P gain / Flux controller Kp
Field-weakening controller P gain / Field_ctrl Kp
2 Parameters
2.3 Parameters for data sets
533