Agilent Technologies ENA Series User Manual page 656

Softkey Functions
Analysis Menu
Key Operation
(Continued)
Fixture Simulator
*1
Topology
*2
Port3 (bal)
Selects test ports 4 and 3 on the analyzer for connection with (balanced)
4-3
port 3 on the DUT (ports c and d in Table 7-8 on page 294) respectively.
Returns to the softkey display screen one level higher.
Cancel
Enables or disables the display of the balanced measurement topology
Property
property. When enabled, calibration status information between test ports
will be displayed in a matrix format in the lower-right corner of the channel
window.
Returns to the softkey display screen one level higher.
Return
*1 Enables or disables the balanced/unbalanced conversion function of active
BalUn
trace. This function uses internal software to convert the results obtained
from an unbalanced test port on the E5070B/E5071B into characteristics of
a balanced port. The port converted into a balanced port will be
characterized by a common mode signal and a differential mode signal.
Measurement parameters are expressed as mixed mode S parameters. Use
the
Topology
test the ports.
Disables the balanced/unbalanced conversion function of all displayed
Balun OFF
*1 traces.
All Traces
Enables the balanced/unbalanced conversion function of all displayed
Balun ON
*1 traces.
All Traces
Measurement
Same as
Displays softkeys for setting up the matching circuit function. Based on the measurement results, the matching
Port Matching
circuit function uses internal software to determine characteristics with a matching circuit inserted between the
DUT and the test ports.
Enables or disables the matching circuit function.
Port Matching
Displays softkeys for selecting the test port to which a matching circuit is added.
Select Port
Selects test port 1 for adding a matching circuit.
1
Selects test port 2 for adding a matching circuit.
2
Selects test port 3 for adding a matching circuit.
*1
3
Selects test port 4 for adding a matching circuit.
*2
4
Returns to the softkey display screen one level higher.
Cancel
Displays softkeys for selecting the type of matching circuit to be added.
Select Circuit
Does not add any matching circuit to the port selected in the
None
menu.
Adds a series L - shunt C type matching circuit to the port selected in the
SeriesL -
ShuntC Select Port
Adds a shunt C - series L type matching circuit to the port selected in the
ShuntC -
SeriesL Select Port
Adds a shunt L - series C type matching circuit to the port selected in the
ShuntL -
SeriesC Select Port
Adds a series C - shunt L type matching circuit to the port selected in the
SeriesC -
ShuntL Select Port
650
Function
to select the type of DUT port and the connection method to
. See "Measurement Menu" on page 701.
menu.
menu.
menu.
menu.
SCPI Command
:CALC{1-16}:FSIM:BAL:TOP:SSB
:CALC{1-16}:FSIM:BAL:TOP:PROP:S
TAT
:CALC{1-16}:FSIM:BAL:PAR{1-16}:ST
AT
None
None
:CALC{1-16}:FSIM:SEND:PMC:STAT
:CALC{1-16}:FSIM:SEND:PMC:
PORT1
:CALC{1-16}:FSIM:SEND:PMC:
PORT2
:CALC{1-16}:FSIM:SEND:PMC:
PORT3
:CALC{1-16}:FSIM:SEND:PMC:
PORT4
:CALC{1-16}:FSIM:SEND:PMC:
Select Port
PORT{1-4} NONE
:CALC{1-16}:FSIM:SEND:PMC:
PORT{1-4} SLPC
:CALC{1-16}:FSIM:SEND:PMC:
PORT{1-4} PCSL
:CALC{1-16}:FSIM:SEND:PMC:
PORT{1-4} PLSC
:CALC{1-16}:FSIM:SEND:PMC:
PORT{1-4} SCPL
Appendix D