Subaru Legacy 2003 Service Manual page 2160

19) Install ATF level gauge guide, and connect ATF
cooler hoses to pipe.
20) Install propeller shaft.
<Ref. to DS-15, INSTALLATION, Propeller Shaft.>
21) Install heat shield cover.
22) Install rear exhaust pipe and muffler assembly.
2.0 L non-TURBO and 2.5 L with OBD models
<Ref. to EX(H4SO)-9, INSTALLATION, Rear Ex-
haust Pipe.> and <Ref. to EX(H4SO)-10, INSTAL-
LATION, Muffler.>
2.0 L non-TURBO and 2.5 L without OBD models
<Ref. to EX(H4SOw/oOBD)-13, INSTALLATION,
Rear Exhaust Pipe.> and <Ref. to EX(H4SOw/
oOBD)-14, INSTALLATION, Muffler.>
3.0 L model
<Ref. to EX(H6DO)-8, INSTALLATION, Rear Ex-
haust Pipe.> and <Ref. to EX(H6DO)-9, INSTAL-
LATION, Muffler.>
2.0 L TURBO model
<Ref. to EX(H4DOSTC)-12, INSTALLATION, Rear
Exhaust Pipe.> and <Ref. to EX(H4DOSTC)-13,
INSTALLATION, Muffler.>
23) Install front and center exhaust pipe. (Non-
TURBO model)
2.0 L and 2.5 L with OBD models
<Ref. to EX(H4SO)-6, INSTALLATION, Front Ex-
haust Pipe.>
2.0 L and 2.5 L without OBD models
<Ref. to EX(H4SOw/oOBD)-10, INSTALLATION,
Front Exhaust Pipe.>
3.0 L model
<Ref. to EX(H6DO)-6, INSTALLATION, Front Ex-
haust Pipe.>
AUTOMATIC TRANSMISSION ASSEMBLY
AT-00683
AT-00682
24) Install center exhaust pipe. (TURBO model)
<Ref. to EX(H4DOSTC)-8, INSTALLATION, Cen-
ter Exhaust Pipe.>
25) Install under cover.
26) Lower the vehicle.
27) Install ATF level gauge.
28) Connect the following connectors.
(1) Transmission harness connectors
(2) Transmission ground terminal
29) Connect the following cables.
(1) Cruise control cable (With cruise control ve-
hicles)
30) Install air cleaner case stay.
Tightening torque:
16 N·m (1.6 kgf-m, 11.6 ft-lb)
31) Install air cleaner case or air intake chamber.
(Non-TURBO model)
2.0 L and 2.5 L models
<Ref. to IN(H4SO)-6, INSTALLATION, Air Cleaner
Case.>
3.0 L model
<Ref. to IN(H6DO)-6, INSTALLATION, Air Intake
Chamber.>
32) Install air intake duct. (Non-TURBO model)
2.0 L and 2.5 L models
<Ref. to IN(H4SO)-7, INSTALLATION, Air Intake
Duct.>
3.0 L model
<Ref. to IN(H6DO)-7, INSTALLATION, Air Intake
Duct.>
33) Install intercooler. (TURBO model)
<Ref. to IN(H4DOSTC)-14, INSTALLATION, Inter-
cooler.>
34) Connect battery ground cable.
35) Fill ATF up to the middle of the "COLD" side on
level gauge by using the gauge hole. <Ref. to AT-
30, Automatic Transmission Fluid.>
36) Take off vehicle from lift arms.
37) Check select lever operation.
<Ref. to AT-49, INSPECTION, Inhibitor Switch.>
38) Check the ATF level. <Ref. to AT-30, Automat-
ic Transmission Fluid.>
39) Check road test.
<Ref. to AT-32, Road Test.>
AT-45
AUTOMATIC TRANSMISSION
AT-00693