Subaru Legacy 2003 Service Manual page 2190

NOTE:
Align ST with torque wrench while tightening AT oil
filter.
ST 498545400 OIL FILTER WRENCH
4) Install front left mud guard. <Ref. to EI-22, IN-
STALLATION, Mud Guard.>
5) Add ATF.
6) Inspect level of ATF. <Ref. to AT-30, Automatic
Transmission Fluid.>
• ATF Filter Assembly
1) Install ATF filter with attachment to bracket.
Tightening torque:
14 N·m (1.4 kgf-m, 10 ft-lb)
2) Install ATF filter assembly to vehicle.
Tightening torque:
16 N·m (1.6 kgf-m, 12 ft-lb)
3) Install AT oil filter. Turn it by hand, being careful
not to damage oil seal.
4) Using ST, tighten AT oil filter.
Calculate AT filter torque specifications using the
following formula.
T2 = L1/(L1 + L2) × T1
T1: 14 N·m (1.4 kgf-m, 10.1 ft-lb)
[Required torque setting]
T2: Tightening torque
L1: ST length 0.078 m (3.07 in)
L2: Torque wrench length
Example:
Torque wrench length
mm (in)
100 (3.94)
150 (5.91)
200 (7.87)
NOTE:
Align ST with torque wrench while tightening AT oil
filter.
ST 498545400 OIL FILTER WRENCH
5) Install hoses to pipe.
NOTE:
Install hoses to pipe aligning marks on them.
6) Install front left mud guard.
<Ref. to EI-22, INSTALLATION, Mud Guard.>
7) Add ATF.
8) Inspect level of ATF. <Ref. to AT-30, Automatic
Transmission Fluid.>
ATF FILTER
Tightening torque
N·m (kgf-m, ft-lb)
7.7 (0.79, 5.7)
9.0 (0.92, 6.7)
10 (1.0, 7.2)
AT-75
3. TURBO MODEL
1) Get new ATF filter and apply a thin coat of ATF
to the oil seal.
2) Install ATF filter. Turn it by hand, being careful
not to damage oil seal.
3) Using ST, tighten ATF filter.
Calculate ATF filter torque specifications using the
following formula.
T2 = L2/(L1 + L2) × T1
T1: 14 N·m (1.4 kgf-m, 10.1 ft-lb)
[Required torque setting]
T2: Tightening torque
L1: ST length 0.078 m (3.07 in)
L2: Torque wrench length
Example:
Torque wrench length
mm (in)
100 (3.94)
150 (5.91)
200 (7.87)
NOTE:
Align ST with torque wrench while tightening ATF
filter.
ST 498545400 OIL FILTER WRENCH
4) Install oil filter wrench assembly.
Tightening torque:
16 N·m (1.6 kgf-m, 10.1 ft-lb)
5) Install surge tank.
<Ref. to IN(H4DOSTC)-22, INSTALLATION, Surge
Tank.>
6) Remove front left mud guard.
<Ref. to EI-22, INSTALLATION, Mud Guard.>
7) Tighten oil filter bracket mounting bolts.
Tightening torque:
16 N·m (1.6 kgf-m, 10.1 ft-lb)
8) Install hoses to pipe.
NOTE:
Align indicated matching marks between hose and
pipe.
9) Install battery.
10) Inspect level of ATF. <Ref. to AT-30, Automatic
Transmission Fluid.>
C: INSPECTION
Replace the part if any defect is found from the in-
spection.
Check for rust, hole, ATF leaks, and other damage.
AUTOMATIC TRANSMISSION
Tightening torque
N·m (kgf-m, ft-lb)
7.7 (0.79, 5.7)
9.0 (0.92, 6.7)
10 (1.0, 7.2)