Subaru Legacy 2003 Service Manual page 2446

10.EXTENSION ASSEMBLY
Thrust washer (50 × 61 × t) to taper roller bearing
table outer race side clearance
0.2 — 0.3 mm T (0.0008 — 0.012 in T)
NOTE:
Clearance should be within the specified value.
Thrust washer (50 × 61 × t)
Part No.
803050060
803050061
803050062
803050063
803050064
803050065
803050066
803050067
803050068
803050069
803050070
803050071
803050072
803050073
803050074
803050075
803050076
803050077
803050078
803050079
Thrust washer to center differential side clearance
0.15 — 0.35 mm (0.0059 — 0.0138 in)
Thrust washer
Part No.
803036050
803036054
803036051
803036055
803036052
803036056
803036053
803036057
803036058
GENERAL DESCRIPTION
Thickness mm (in)
0.50 (0.0197)
0.55 (0.0217)
0.60 (0.0236)
0.65 (0.0256)
0.70 (0.0276)
0.75 (0.0295)
0.80 (0.0315)
0.85 (0.0335)
0.90 (0.0354)
0.95 (0.0374)
1.00 (0.0394)
1.05 (0.0413)
1.10 (0.0433)
1.15 (0.0453)
1.20 (0.0472)
1.25 (0.0492)
1.30 (0.0512)
1.35 (0.0531)
1.40 (0.0551)
1.45 (0.0571)
Thickness mm (in)
0.9 (0.035)
1.0 (0.039)
1.1 (0.043)
1.2 (0.047)
1.3 (0.051)
1.4 (0.055)
1.5 (0.059)
1.6 (0.063)
1.7 (0.067)
MT-5
MANUAL TRANSMISSION AND DIFFERENTIAL
11.FRONT DIFFERENTIAL
Bevel gear to pinion backlash
0.13 — 0.18 mm (0.0051 — 0.0071 in)
Washer (38.1 × 50 × t)
Thickness
Part No.
mm (in)
0.925 —
803038021 0.950 (0.0364
— 0.0374)
0.975 —
803038022 1.000 (0.0384
— 0.0394)
Pinion shaft to axle drive shaft clearance
0 — 0.2 mm (0 — 0.008 in)
Snap ring (Outer-28)
Thickness
Part No.
mm (in)
805028011 1.05 (0.0413)
12.TRANSFER DRIVE GEAR
Snap ring (Outer-30) to ball bearing clearance
0.01 — 0.15 mm (0.004 — 0.0050 in)
Snap ring (Outer-30)
Part No.
805030041
805030042
805030043
Thickness
Part No.
mm (in)
1.025 —
803038023 1.050 (0.0404
— 0.0413)
— —
Thickness
Part No.
mm (in)
805028012 1.20 (0.0472)
Thickness
mm (in)
1.53 (0.0602)
1.65 (0.0650)
1.77 (0.0697)