AGFA Avantra 36/44 Service Manual page 489

Racks, OLP 2-9
Ready Mode 2-2, 2-3
Rear exit panel 1-6
Rear Exit Panel (Top) 1-6
Rear Leveler Feet 1-15
Rear Lower Panel 1-6
Rear Top Cover 1-6
Rear Top Side Panel 1-6
Receiver basket 1-6
Red (Developer) Hose 1-26
Removing Foam from Dryer Section 1-26
Removing Tape from Door 1-26
Repair Method Tables
how to use 4-17
Repair Steps 4-21
Replacing the Roller 1-28
Replenishment 2-9
topping-up 2-10
Replenishment Hoses, Installing 1-31
Replenishment Pumps
adjust 4-12
Replenishment Pumps Calibration 4-12
Replenishment, Manual 2-10
Reposition the Control Panel 4-7, 4-11
Rewiring 1-18
Rewiring for Different Operations 1-19
Right Lower Door 1-6
Right Lower Door (Hinged) 1-25
Right Side Cover 1-28
Roller Removal 1-9
Rollers
crystillization 2-3
RS-232 ATB 2-5
RS-232 OLP Com. 2-5
Run Mode 2-9
Running the Service Program 4-14
S
Safety Switches 2-4
Schmitt-Trigger Output 2-8
Sensor
dryer section temperature 3-19
functions 2-3
wet section temperature 3-18
Sensor, Temperature 4-2
Sensors 2-8
film 2-8
operating parameters 2-8
optical interrupter 2-8
reattaching 1-14
temperature 2-8
Sensors and Switches
diagram 4-24
Service Program 4-14
Service Program Codes 4-16
Servicing
on-line processor 4-2
Setting the Jumpers
LCB settings 4-5
LPB settings 4-5
Section IV: On-Line Processor
Shipping Crates, OLP 1-5
Side Panels
front 1-24
rear 1-24
Solenoid Valve 1-16
Space Requirements
on-line processor 1-2
Specifications A-1
on-line processor A-1
physical
OLP A-1
Specifications, On-line Processor (OLP) A-1
Stabilizer Bar 1-13
Stabilizer Brace 1-15
Standby Mode 2-9
Standby Mode, OLP 2-2
Standoffs
bottom of cratae 1-11
four corners of the frame 1-11
Status and Error Messages 4-25
Steps for Connecting Water Supply/
Drainage 1-16
Steps, Repair 4-21
Striker Plate 1-25
Supply Voltage 1-18
Support Leg 1-15
Switch Settings 4-11
Switches and Sensors 4-24
T
Tables
repair method 4-17
Tank Capacity 1-16
Tank Capacity, Water 1-16
Taping the Door 1-9
Temp Sensor 2-4
Temperature
checking 4-3
difference between fixer and water 1-15
sensor 2-8, 4-2
settings 1-16
water 1-15
Temperature Control
circulation pumps 2-9
fixer 2-9
immersion heaters 2-9
Temperature Range 1-16
Temperature Range, Developer 1-16
Temperature Sensor 2-8, 3-18, 3-19
Timed Replenishment 2-9
Tools Required for OLP Unpacking 1-3
Top Covers
forward (front) 1-34
locations 1-34
middle 1-34
order of placement 1-34
rear 1-34
Top overs 1-34
Top Side Panel 1-25
Index I-5