AGFA Avantra 36/44 Service Manual page 272

Command Files 3-25
Commands
Batch 3-26
Diagnostic 3-44
Enter Service Mode 1 3-44
Hang-up 3-67
New Engine/Restart 3-44
Reset 3-44
Soft Reset 3-44
SPI 3-26
Communication Port 3-45
Component Removal/Replacement
Procedures 4-1
Config Comm. Port 3-45
configuration 3-65
Configuration, Imagesetter 3-44
Configuration, Local Modem 3-65
Configuration, Port 3-44
Configuration, Remote Modem 3-63
Configuring the Local Modem 3-65
Connecting the Local Modem 3-65
Connecting the Remote Modem 3-64
Connection, Remote 3-67
Control Panel Assembly 4-30
Core Tests Level One 3-3
Correct Voltages 5-11
Correction SRAM Checksum Test 3-7
Correction SRAM Test 3-7
Correction State Machine 3-7
Correction Tables, creating 3-56
Cover, Electronic Enclosure 4-8
Covers
remove and replace 4-3
Crossbars
location 1-6
CSDM 2-4, 2-10, 2-11, 4-28
CSDM PCB
location 4-28
Current Offset, Supply Motor 5-14
Customer Application Training 1-24
Customer Pre-site Checklist
environment 1-2
film processor requirements 1-3
miscellaneous
cables 1-4
densitometer 1-4
doorways 1-3
elevator 1-3
power requirements 1-1
telephone requirements 1-3
work space 1-2
Cutter Assembly
location 4-21, 4-22, 4-23
remove and replace 4-20
remove/replace 4-20
Cutter Home Sensor
location 4-22
Cutter Interlock Switch Cable
location 4-10
Cutter Morot
shaft 4-22
Cutter Motor
coupler 4-22
remove and replace 4-22
remove/replace 4-22
D
DAC 2-10, 3-9
DAC Loop Backs 3-9
DAC RAMPS Tests 3-22
DAC Register Test 3-6
DC Motor/Solenoid 2-12
DC Rewind Motors 2-26
DC Spindle A/B Gear Motor 2-26
DEC 2-4, 2-5, 2-12, 2-14, 3-3, 3-9, 3-10, 3-19,
3-27, 3-29, 3-35, 4-25, 5-2
DEC Board
location 4-27, 4-35
DEC Correction Tables
saving 3-51
DEC DSP Correction Tables
saving/restoring 3-51
DEC EEPROM 3-27, 3-29
DEC FLASHROM 3-51
DEC K-4
masteship role 3-3
DEC Machine Parameters 3-29
save/restore 3-49
DEC Micro-controller 3-8, 3-9
DEC Micro-controller Test Descriptions 3-8
DEC Offgate Register Test 3-8
DEC Ongate Register Test 3-8
DEC Tests 3-21
DEC to DSP SPI Link Test 3-8
DEC Vacuum Register Test 3-8
DEC-K4 3-3
slave mode 3-4
subsystem tests 3-4
DEC-K4 Micro-controller 3-4
Density Settings 5-11
Detector, Take-up Media Present 4-23
DIAG 3-9, 3-10
slave mode 3-4
DIAG Micro-controller 2-4, 3-3
master device 3-3
DIAG Micro-controller Test Descripions 3-6
DIAG Processor 3-10
Diagnostic Commands 3-44
Diagnostic Firmware 3-11
Diagnostic Program 3-17
Diagnostic Program (AVDIAG) 3-19
Diagnostic Program, Starting 3-19
Diagnostic Serial Port 3-19, 3-49, 3-52
Diagnostic Session 3-67
Diagnostic Software 3-19
Diagnostic Tool, Direct Connect 3-17
Diagnostic Tools 3-1
Diagnostics, Power-up Boot 3-2
Section I: Imagesetter
Index I-3