AGFA Avantra 36/44 Service Manual page 278

polarizer 2-16, 4-50
take-up media present 4-23
Sensor Driver Module (SDM) 2-11
Sensor Problems, Troubleshooting 3-39
Sensor, Focus Home 2-11
Sensor, Polarizer Home 2-11
Sensor, Polarizer Rotation 4-51, 4-55
Sensor, Spot Changer 4-50
Sensor, Spot Changer Home 2-11
Sensor, Supply Cassette Spindle A/B
Position 4-64
Sensor, Supply Jam 2-27
Sensor, Supply Media Present 2-27
Sensor, Take-up Jam 4-16
Sensors 2-12
beam compression 2-16, 4-50
beam compressor 4-53
focus 2-16, 4-50, 4-55
polarizer 4-51, 4-52
spot size 2-16, 4-50, 4-51
supply spindle select A/B 4-64
take-up jam 4-16
Sensors, Display 3-39
Sensors, Supply Spindle Select A/B 4-64
Sequence, Power-up Boot 3-3
Serial Communication 3-3
Serial Peripheral Interface (SPI) bus 2-3
Serial Peripheral Interface (SPI) Communica-
tion Mode 3-3
Serial/modem Cable 4-25
Service Engineer Installation Procedure 1-4
pre-installation checks 1-4
Servo 2-12
Session, Remote 3-66
Set Config Passwd Menu 3-47
Setting the S-Current Offset Field 5-15
SGM 2-15, 2-16, 3-28, 4-49
SGM Motor Connector
location 4-28
SGM Sensor Connector
location 4-28
SGM-A/B Mod Align 3-28
Shield Locking Knobs 1-18
Side Cover
thumb screw location 4-4
Side Covers
remove and replace 4-3
Slack Loop Test Procedure 5-21
SMM 4-47
Soft Reset 3-44
Soft Reset Command 3-44
Soft Vacuum
defined 6-5
Software Installation Procedure
diagnostics 3-18
Software, Diagnostic 3-19
Specifications, Avantra Modem 3-62
SPI 3-26
SPI Bus 2-4, 3-3
mastership 3-4
SPI commands 3-26
SPI Communication Link 3-41
SPI Communication Tests 3-4
SPI communication tests 3-4
SPI Communications Verify 3-10
Spin Motor 2-19
alignment key 4-48
encoder cable 4-48
Spin Motor Assembly
location 4-43
Spin Motor Mirror Cleaning Procedure 6-3
Spin Motor Module 2-15, 2-18, 4-48
encoder 2-19
mirror 2-19
remove and replace 4-47
spin motor 2-19
Spindle A/B Gear Motor 2-26
Spindle A/B Position Sensors
location 4-57
Spindle A/B Sensors 2-27
Spindle Feeds
equalizing 5-14
Spinner Motor 3-4
Spinner Verify Test 3-10
Spot Changer 2-10
Spot Changer Home Sensor 2-11
Spot Forming Lens 2-17
location 2-16, 4-50
Spot Generation Module
laser diode mount 2-17
polarizer 2-17
spot forming lens 2-17
spot size changer 2-17
weak lens 2-18
Spot Generation Module (SGM) 2-15, 2-16
remove and replace 4-49
Spot Size Changer 2-17
location 2-16, 4-50
Spot Size Sensor
location 2-16, 4-50, 4-51
remove and replace 4-50
Spring Clips
location 1-5
SPVAPIS Serial Interface 2-9
SRAM 3-4
SRAM Checksum Test 3-7
S-Spind Fwd Assist
definition 3-33
Starting the Diagnostic Program 3-19
Statistics
operational 3-52
Statistics, Operational 3-37
Stepper 2-12
Subsystem Tests
DEC-K4 3-4
Supp/Tkup Delay
definition 3-33
range 3-33
Section I: Imagesetter
Index I-9