AGFA Avantra 36/44 Service Manual page 486

Avantra 36/44 Service Manual
Crystallization 2-3
D
Data Communication Link
between LCB and ATB 2-5
between LCB and imagesetter 2-5
Default Replenishment Amount, Developer 2-
10
Default Replenishment Amount, Fixer 2-10
Default wiring 1-18
Description of Inputs and Outputs
(P/N 52024000100) 2-8
Description of Inputs and Outputs, ATB 2-8
Description of LCB Inputs and Outputs 2-4
Description of OLP Boot-up Procedures 2-2
Developer 1-27, 1-33
Developer Anti-oxidation Cover 1-6
Developer Default Replenishment Amount 2-
10
Developer Filter 1-24
Developer Pump 3-16
Developer Rack 1-6
Developer/fixer Crossover Guide 1-6
Developing 1-15
Diagram, Troubleshooting 4-20
Digital Voltmeter (DVM) 1-13
Dimensions, Buffer 1-2
Dimensions, Imagesetter 1-2
Dimensions, OLP 1-2
Doors
left lower 1-25
right lower 1-25
Drain 1-16
Drain Configurations
compliance 1-16
Drainage 1-15
Drip Tray, Placing 1-26
Drip Tray. 1-6
Drive Belt 3-26
Drive Motor 3-2
Drive Shaft 3-27
Dryer Blower 3-23, 3-24, 3-25
Dryer Blower Motor Assembly 3-20
Dryer Element 3-22
Dryer Heater Element 3-20, 3-21
Dryer Heating Elements 3-24
Dryer Section Temperature Sensor 3-19
E
EEPROM 3-8
Electrical Connection
compliance 1-17
Electrical Connections
on-line processor 1-17
Electrical Supply 1-17
on-line processor 1-17
Electrical, Imagesetter 1-3
Electrical, OLP 1-2, A-2
Electronics 2-3
on-line processor
I-2 Index
Luth computer board (LCB) 2-3
Electronics Box 3-4, 3-5, 3-6, 3-12
Engine Crate 1-5, 1-8
Entrance Rack Assembly 1-20
Entry Rack Assembly 3-26
Error Messages 4-25
Evaporation 2-9
Evaporation Cover 1-6
Evaporation Covers Location 1-33
Exit Jam
error message 4-25
F
Fahrenheit/centigrade Jumper 3-8
Fan 1-10
Film Sensors 2-8
Filter Housing, Installing 1-30
Filter Parts 1-6
Filtration Rate 1-15
Fixer 1-27
Fixer Anti-oxidation Cover 1-6
Fixer Default Replenishment Amount 2-10
Fixer Pump 3-16
Fixer Rack 1-6
Fixer Replenishment Pump 3-15
Fixer/wash Crossover Guide 1-6
Fixing 1-15
Floor Load 1-2
on-line processor 1-2
Fluid Containers, Placing 1-26
Forward Top Cover 1-6
Front Left Side Cover 1-24
Front Left Vent Cover 1-20
Front Leveler Feet 1-14
Front Panel 1-6, 1-20
Front Right Side Cover 1-24
Front Right Vent Cover 1-20
Front Top Side Panel (Control) 1-6
Fuse Connectors 3-8
Fuses, Jumper 3-9
G
Grey (Water Supply) Hose 1-26
H
Heating Element 3-17
Heating Elements 3-24
I
Idle Mode 2-2, 2-3
Imagesetter Dimensions 1-2
Imagesetter Electrical 1-3
Immersion Heaters 2-9
Inner Cover for Entrance Rack 1-6
Input Jam
error message 4-25
Input Sensors 2-4
Input Wiring Connections
location 1-18
Inputs and Outputs, LCB 2-4