AGFA Avantra 36/44 Service Manual page 271

Avantra 36/44 Service Manual
Board
carriage 4-49
DEC 4-35
digital engine controller 4-25
SDM 4-13, 4-20
Boards
carriage 4-50
carriage sensor driver (CSDM) 4-28
BOL 5-2
Boot Error Codes 3-13
Boot Tests 3-24
Bottom Front Panel 4-5
Bottom Panel
location 4-7
BrdgeOffEly Time
definition 3-31
Bridge 6-5, 6-8
Bridge Cleaning 6-8
Bridge Maintenance 6-5
Bridge Max. Torque
definition 3-31
Bridge Primitives 3-43
Bridge Tests 3-24
Bridge Tie Down Bracket 1-16
Buffer Med Spd
definition 3-31
C
Carriage 1-20, 1-21
Carriage Align Test 5-14
Carriage Alignment 3-29
Carriage Assembly 2-19, 4-42
home position 5-5
remove and replace 4-42
Carriage Board 4-49, 4-50
location 4-43
Carriage Digital Motor/encoder 2-10
Carriage Drive DC Servo Motor/Encoder 2-10
Carriage Drive Removal/Replacement
Procedures 4-40
Carriage Encoder Alignment Procedure 5-14
Carriage Encoder Signal 3-8
Carriage Home Position Alignment
Procedure 5-5
Carriage Home Position Sensor 2-21
Carriage Installation from Transfer Tool 4-45
Carriage Motion 3-41
Carriage Motion Menu 3-41
Carriage Rail Cleaning Procedure 6-2
Carriage Removal to Transfer Tool 4-42
Carriage Sensor Driver (CSDM) PCB
remove and replace 4-28
Carriage Sensor Driver Module (CSDM) 2-4,
2-10
Carriage Sensor Driver Module PCB (CSDM)
(left side)
location 4-29
Carriage sensor Driver Module PCB (CSDM)
(right side)
location 4-28
I-2 Index
Carriage Test 3-8
Carriage Tests 3-22
Carriage Transfer Tool
alignment lip 4-45
alignment pin
location 4-40
assembling 4-40
bearing retainer bracket 4-43
carriage bearings 4-43
carriage rails 4-41
carriage stop pin
location 4-40
left rail alignment pin
location 4-40
locking pin
location 4-40
locking pins 4-45
magnet bracket 4-43
retainer screws 4-43, 4-45
retaining bracket screws
location 4-40
screw 4-41, 4-45
Carriage Transfer Tool Installation 4-40
Carriage, Unlocking the 1-20, 1-21
Cassette Housing 2-33
Cassette Parameters 3-37, 3-52
Cassette Parameters Menu 3-37
Cassette, Powered Media Take-up 2-27
Cassette, Supply 2-32
Center Channel Bolts 1-9
Chafe Direction Shield 4-19
chafe direction shield 4-19
Chafe Tray 1-13
Chafe Tray Hook 1-19
Chafe Tray, Inserting The 1-19
Channel Beams 1-8
Checklist, Customer Pre-site 1-1
Checksum
correction SRAM 3-7
Internal ROM 3-8
Checksums
2400 correction table 3-4
3600 correction table 3-4
Cheksum
FLASHROM 3-7
Cleaning Exterior 6-5
Cleaning for Customer 6-4
Cleaning Inner System 6-7
Cleaning Lower Interior Area 6-7
Cleaning Procedure, Carriage Rail 6-2
Cleaning Procedure, Spin Motor Mirror 6-3
Cleaning Supply/Take-up Cassette Area 6-6
Cleaning Take-up Module Area 6-6
Cleaning the Bridge 6-8
Close Log File 3-25
Coefficient Tables,DSP 3-4
Command
Reset 3-67
Command File Format 3-26