Honda Transalp XL700V Manual page 365

FRONT WHEEL/SUSPENSION/STEERING
SERVICE INFORMATION
GENERAL
• Riding on damaged rims impairs safe operation of the vehicle.
• A contaminated brake disc or pad reduces stopping power. Discard contaminated pads and clean a contaminated disc
with a high quality brake degreasing agent.
• A hoist or equivalent is required to support the motorcycle when servicing the front wheel, fork and steering stem.
• For hydraulic brake system service (page 15-4).
SPECIFICATIONS
Minimum tire tread depth
Cold tire Driver only
pressure
Driver and passenger
Axle runout
Wheel rim Radial
runout
Axial
Wheel balance weight
Fork Spring free length
Tube runout
Recommended fork fluid
Fluid level
Fluid capacity
Steering head bearing pre-load
TORQUE VALUES
Handlebar holder bolt
Handlebar lower holder nut
Front axle
Front axle holder nut
Front brake disc bolt
Fork center bolt
Fork cap
Fork top bridge pinch bolt
Fork bottom bridge pinch bolt
Steering top thread
Steering stem nut
Front master cylinder holder bolt
Front brake caliper mounting bolt
Front wheel pulser ring torx bolt (ABS type)
Spoke
Brake lever pivot bolt
Brake lever pivot nut
Throttle housing screw
Right handlebar switch screw
13-4
ITEM
27 N·m (2.8 kgf·m, 20 lbf·ft)
26.5 N·m (2.7 kgf·m, 20 lbf·ft)
64 N·m (6.5 kgf·m, 47 lbf·ft)
12 N·m (1.2 kgf·m, 9 lbf·ft)
42 N·m (4.3 kgf·m, 31 lbf·ft)
20 N·m (2.0 kgf·m, 15 lbf·ft)
22 N·m (2.2 kgf·m, 16 lbf·ft)
26 N·m (2.7 kgf·m, 19 lbf·ft)
34 N·m (3.5 kgf·m, 25 lbf·ft)
103 N·m (10.5 kgf·m, 76 lbf·ft)
12 N·m (1.2 kgf·m, 9 lbf·ft)
30 N·m (3.1 kgf·m, 22 lbf·ft)
8 N·m (0.8 kgf·m, 5.9 lbf·ft)
3.7 N·m (0.4 kgf·m, 27 lbf·ft)
1.0 N·m (0.1 kgf·m, 0.7 lbf·ft)
5.9 N·m (0.6 kgf·m, 4.4 lbf·ft)
4.2 N·m (0.4 kgf·m, 3.1 lbf·ft)
0.9 N·m (0.1 kgf·m, 0.7 lbf·ft)
STANDARD
–
2
200 kPa (2.00 kgf/cm , 29 psi)
2
200 kPa (2.00 kgf/cm , 29 psi)
–
–
–
–
621.4 (24.47)
–
Honda ULTRA CUSHION OIL 10W or
equivalent
104 (4.1)
598 ± 2.5 cm (20.2 ± 0.08 US oz,
3
21.0 ± 0.09 Imp oz)
10.8 – 15.7 N (1.1 – 1.6 kgf)
ALOC bolt; replace with a new one.
Apply locking agent.
– See page 13-34
ALOC bolt; replace with a new one.
ALOC bolt; replace with a new one.
Unit: mm (in)
SERVICE LIMIT
1.5 (0.06)
–
–
0.2 (0.01)
2.0 (0.08)
2.0 (0.08)
60 g (2.1oz)
max.
609.0 (23.97)
0.20 (0.008)
–
–
–
–