GBC StreamPunch Ultra Service Manual page 82

ARP 2.28.6 Skew Sensor Board (S6 - S10) Replacement ........... 4-70
ARP 2.28.7 Alignment Sensor Board (S11 - S15) Replacement . 4-71
ARP 2.28.8 Backage Sensor Board (S16, S17) Replacement ..... 4-73
ARP 2.29 Motor Driver (Stepper Board) Replacement ..................... 4-74
ARP 2.30 Solenoid Replacement ..................................................... 4-75
ARP 2.30.1 Diverter Solenoid Replacement ................................. 4-75
ARP 2.30.2 Entrance Idler Solenoid Replacement ....................... 4-77
ARP 2.30.3 Acceleration Roller Idler Solenoid Replacement ....... 4-77
ARP 2.30.4 Exit Idler Solenoid Replacement ................................ 4-78
ARP 2.31 Upper Bypass Panel Anti-Static Brush Replacement ...... 4-78
3. Punch Module
ARP 3.1 Punch Module Replacement ............................................ 4-79
ARP 3.1.1 Punch Module Removal ............................................. 4-79
ARP 3.1.2 Punch Module Installation .......................................... 4-83
ARP 3.2 Chip Tray Home Switch Replacement ............................. 4-84
ARP 3.3 Chip Level Emitter Replacement ...................................... 4-85
ARP 3.4 Chip Level Receiver Replacement ................................... 4-85
ARP 3.5 Punch Motor Replacement ............................................... 4-86
ARP 3.6 Punch Motor Belt Replacement (Timing Belt) .................. 4-87
ARP 3.7 Clutch or Clutch Pulley Replacement ............................... 4-89
ARP 3.8 Punch Alignment Stepper Motor and Pulley Replacement,
and Alignment Stepper Bracket Replacement ................. 4-92
ARP 3.9 Steering Module Replacement ......................................... 4-93
ARP 3.10 Ground Strap Replacement.............................................. 4-96
ARP 3.11 Alignment Carriage Sub Assembly Replacement ............ 4-98
ARP 3.12 Steering Stepper Motor Replacement ............................ 4-101
ARP 3.13 Steering Motor Belt (65 Groove) Replacement .............. 4-103
ARP 3.14 Steering Drive Roller Shaft Replacement ...................... 4-105
ARP 3.15 Steering Idler Panel Weldment Replacement ................ 4-107
ARP 3.16 Steering Idler Roller Assembly Replacement ................. 4-109
ARP 3.16.1 Steering Idler Roller Bearing Replacement ............. 4-111
ARP 3.17 Steering Drive Panel Weldment Replacement ............... 4-112
ARP 3.18 Die Lock Plunger and Stripper Assembly Replacement 4-113
ARP 3.19 Punch shaft Ball Bearing Replacement .......................... 4-114
ARP 3.20 Die Stop Magnet Replacement ...................................... 4-114
Adjustments/Repairs
ARP 3.21 Die Lock Handle Replacement ...................................... 4-115
ARP 3.22 Die Lock Shaft Replacement ......................................... 4-116
ARP 3.23 Die Rail Assembly and Die Rail Springs Replacement . 4-118
ARP 3.24 Alignment Sensor Bracket and Alignment Sensor Bottom
Guide Replacement ....................................................... 4-120
ARP 3.25 Punch Module Mount Pin Replacement ........................ 4-122
ARP 3.26 Backgage Sensor Bracket Weldment and Backgage Sensor
Lower Bracket Replacement ......................................... 4-123
ARP 3.27 Die Set Recognition Replacement................................. 4-124
4. Power Supply
4-79
ARP 4.1 24V Power Supply Replacement ................................... 4-125
ARP 4.2 AC Filter Replacement .................................................. 4-127
5. Electronics and Control
ARP 5.1 Main Control Board Replacement ................................. 4-128
ARP 5.2 Comm Board Replacement ........................................... 4-130
ARP 5.3 Dieset Recognition Reader Board Replacement ........... 4-131
6. Adjustments
ADJ 1.1 Door Latch Adjustment .................................................. 4-132
ADJ 1.2 Diverter Solenoid Adjustment ........................................ 4-133
ADJ 1.3 Die Stop Magnet Adjustment ......................................... 4-135
ADJ 1.4 Timing Belts Adjustment ................................................ 4-136
ADJ 1.5 Punch clutch Indexing ................................................... 4-141
ADJ 1.6 Dieset Recognition Board Adjustment ........................... 4-145
ADJ 1.7 Idler Panel Magnetic Latches Adjustment ..................... 4-146
ADJ 1.8 Drive Panel Position Adjustment ................................... 4-147
02-03-2017
4-2
GBC StreamPunch Ultra/Ultra MP
4-125
4-128
4-132